Which Rack'Em Grass Catcher Fits Ariens IKON XD-52

Question

Question:

Do you have a grass catcher for a Ariens IKON XD-52?

asked by: Matt

1

Helpful Expert Reply:

I checked with Rack'em and the Grass Catcher part # RCMMS4 is a fit for your Ariens IKON XD-52.

expert reply by: Jameson C

1

Answer 1

We have a Rackem' catcher that will work but the RCMMS4-OBS1 is not designed for that mower. Instead you will use the Rack'em Grass Catcher for Toro, Bobcat, and Exmark Lawn Mower part #RCMMS4-EXS1.

view full answer...

Answer 2

The Rack'em Multi-Mount Grass Catcher part #RCMMS4 works with any riding lawn mover where the discharge opening is even with or extends out further than the mower's rear wheel. If so, then you'd need to make a custom face…

view full answer...

Answer 3

When it comes to installing a grass catcher on your Ariens Ikon XD The Rack'Em Multi-Mount Grass Catcher - Aluminum and Stainless Steel #RCMMS4 will work for you. The faceplate is sold separately #RA54FR. I attached a review video link…

view full answer...

Answer 4

The correct catcher will depend on the discharge opening behind that deflector shown in your photo. If it has the deck with a Z-bracket as shown in the provided photo, you'd use #RCMMS4-EXS1-TORO. If it doesn't have the z-slot, but…

view full answer...

Answer 5

The Rack'em Grass Catcher for Toro Lawn Mower with Z-Cut Deck #RCMMS4-EXS1-TORO will fit your 52 inch Toro Z mower deck if it has the Z-cut deck (it should but you might still check). If you have the regular deck then you will use #RCMMS4-EXS1…

view full answer...

Answer 6

If your Toro Timecutter has the Z cut deck that extends out further than the rear wheel, you'd use the Rack 'Em #RCMMS4-EXS1-TORO catcher. If you have the regular deck, you'd use #RCMMS4-EXS1. The Z deck has notches or slots in it as…

view full answer...

Answer 7

The correct Grass Catcher for your Scag Liberty Z48 is the part #RCMMS4-OBS1.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Which Rack'Em Grass Catcher Fits Ariens IKON XD-52

Product Page this Question was Asked From

Continue Researching