Would Draw Tite Hitch 36548 Fit 2020 Dodge Charger Scat Pack

Question

Question:

Need a little guidance about this hitch!!! Will it fit under a 2020 scat pack charger without having to destroy the rear valance????

asked by: Brad Y

0

Expert Reply:

The Draw Tite hitch part # 36548 does fit your 2020 Dodge Charger Scat Pack but will require some trimming of the lower rear fascia. I wouldn't say it would destroy the valence but it does require trimming which is a very common step for the install of hitches.

expert reply by: Jameson C

0

Answer 1

The trailer hitch I recommend for your 2016 Dodge Charger is the Draw-Tite Trailer Hitch Receiver, Class II #36548. This trailer hitch has a 1-1/4 inch receiver that will work well with your Thule Vertex. The #36548 hitch has been confirmed to fit…

view full answer...

Answer 2

In order to install a trailer hitch on a 2019 Dodge Challenger with aftermarket exhaust, the best option we have for you is the Curt Trailer Hitch Receiver part #C13236 not the Draw-Tite Max-Frame Trailer Hitch Receiver part #76145. The Curt hitch as…

view full answer...

Answer 3

The least visible hitch we have for your 2016 Dodge Charger Scat Pack is going to be the Draw Tite #36548 that you referenced. This hitch has a 1-1/4 inch opening which would be smaller than the 2 inch hitches and due to it's safety chain loop…

view full answer...

Answer 4

When we installed the Draw-Tite Max-Frame Trailer Hitch Receiver #76145 on a 2018 Dodge Challenger we found that from the ground to the top of the inside of the receiver measured 9-1/4" as you can see in the attached photo. It might be a little…

view full answer...

Answer 5

For a 3-bike platform rack the Kuat Transfer part #KU24FR would be a great option. We had the chance to test fit this rack on a similar 2015 Chrysler 300 and it fit and worked well. Check out the review video I attached that shows this. Platform bike…

view full answer...

Answer 6

We have both Class II and III trailer hitches available for your 2011 Dodge Charger R/T. If you are going to use Class III hitch #C13093 then I recommend etrailer ball mount kit #989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip,…

view full answer...

Answer 7

For your 2011 Dodge Charger we have the Draw Tite trailer hitch part #76145 which is a confirmed fit and has plenty of tongue weight capacity for a carrier with a Pride 1450 as this hitch has a tongue weight of 675 lbs. You'd have to verify in…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Would Draw Tite Hitch 36548 Fit 2020 Dodge Charger Scat Pack

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching