Trailer Hitch Kit Recommendation for a 2011 Dodge Charger R/T

Question

Question:

I know what trailer hitch to get, what about the receiver , ball etc. 2011 dodge charger r/t , wiring also

asked by: John J

0

Expert Reply:

We have both Class II and III trailer hitches available for your 2011 Dodge Charger R/T. If you are going to use Class III hitch # C13093 then I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a storage bag. If you also need a 2-5/16 inch use # 63847. For trailer wiring use # 118560.

If you are using a Class II trailer hitch, like Curt Class II hitch # C12064 or Draw-Tite hitch # 36548, you can use ball mount # C45520.

For any of the Class II hitches you can use 1-7/8 inch ball # 19256 or 2 inch ball # 19258.

I have linked installation instructions as well.

expert reply by: Chris B

0

Answer 1

For your 2014 Dodge Charger the Curt Hitch part #C12064 is a confirmed fit. It has the towing capacity of 3,500 lbs total trailer weight. This means it would easily tow a PWC trailer like what you have. For a ball mount you would want the part…

view full answer...

Answer 2

I called my contact at Curt and asked about the Trailer Hitch Receiver, part #C12064. They said they could not guarantee it would fit your Hellcat. It is a Class ll hitch and has a 1-1/4 inch receiver opening. I also called Draw-Tite and asked about…

view full answer...

Answer 3

The Draw-Tite Class II Trailer Hitch Receiver, #36548, will fit a 2016 Dodge Challenger if your vehicle does not have the quad-tip exhaust. Since your model is the Hellcat, I am assuming that your vehicle will have the quad-tip exhaust. I recommend…

view full answer...

Answer 4

For your 2011 Dodge Charger we have the Draw Tite trailer hitch part #76145 which is a confirmed fit and has plenty of tongue weight capacity for a carrier with a Pride 1450 as this hitch has a tongue weight of 675 lbs. You'd have to verify in…

view full answer...

Answer 5

The least visible hitch we have for your 2016 Dodge Charger Scat Pack is going to be the Draw Tite #36548 that you referenced. This hitch has a 1-1/4 inch opening which would be smaller than the 2 inch hitches and due to it's safety chain loop…

view full answer...

Answer 6

When we installed the Draw-Tite Max-Frame Trailer Hitch Receiver #76145 on a 2018 Dodge Challenger we found that from the ground to the top of the inside of the receiver measured 9-1/4" as you can see in the attached photo. It might be a little…

view full answer...

Answer 7

I went out and took the measurement on both hitches for you. The Draw-Tite, part #76145, measures about 9 inches from the top of the wings where the hitch mounts to the vehicle's frame to the bottom of the collar around the receiver opening. The…

view full answer...

Answer 8

In order to install a trailer hitch on a 2019 Dodge Challenger with aftermarket exhaust, the best option we have for you is the Curt Trailer Hitch Receiver part #C13236 not the Draw-Tite Max-Frame Trailer Hitch Receiver part #76145. The Curt hitch as…

view full answer...

Answer 9

For a 3-bike platform rack the Kuat Transfer part #KU24FR would be a great option. We had the chance to test fit this rack on a similar 2015 Chrysler 300 and it fit and worked well. Check out the review video I attached that shows this. Platform bike…

view full answer...

Answer 10

If you do not have a hitch on your 2011 Chrysler 300, I recommend a hitch and a cargo carrier. After doing some research on your vehicle I found that the towing weight capacity is 1,000 lbs. that means the maximum tongue weight capacity or total…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Trailer Hitch Kit Recommendation for a 2011 Dodge Charger R/T

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching