Can Two Thule Hullavator Pro Kayak Carriers Be Mounted On A 2015 Subaru Forester Roof?

Question

Question:

Hi, I purchased 2 thule hullavators last November from etrailer. I have a 2015 Subaru Forester and would like to be able to transport 2 kayaks. I do have the side rails. I need to know what length cross bars I need and also the attachments that are needed. Thank you.

asked by: Deborah A

0

Expert Reply:

The Thule Hullavator Pro - Lift Assist Kayak Carrier # TH898 requires about 28-1/2" of crossbar space and also requires the crossbars to overhang at least 4" on each side. Aside from that, the Hullavator weighs 40lbs each. It is not recommended to try and use two Hullavators on one roof.

I recommend using one Hullavator for one kayak, and then for the other kayak use the Malone DownLoader Kayak Carrier with Tie-Downs - J-Style - Folding - Side Loading # MPG114MD. The Malone DownLoader only weighs about 12lbs and has a weight capacity of 75lbs. This can clamp onto crossbars or be mounted on the top track by using Aero Style Crossbar T-Slot Fit Kit for Malone Kayak Carriers # MPG8287.

For a roof rack that will accommodate your two kayaks, I recommend looking into Malone AirFlow2 Roof Rack - Aero Crossbars - Raised, Factory Side Rails - Aluminum - 58" Long # MPG216. This is a very affordable but useful option as it is 58" long which is long enough for your application. The weight capacity for this setup is 165lbs. The has the top channel which allows the kayak carriers and other accessories to be easily installed. I attached demonstration videos for you.

expert reply by: Andrew N

0

Answer 1

The minimum cross bar spread to install the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs part #TH898 is 24" apart. So the bars must be at least 24" apart for safe use. The maximum cross bar spread is 36" so it only…

view full answer...

Answer 2

The Thule Hullavator part #TH898 takes up a max of 28-1/2 inches of bar space so if you installed a roof rack that has crossbars that are around 60 inches you could fit two of them. So then for a roof rack your best option would be the Malone Rack…

view full answer...

Answer 3

Yes two of the Thule Hullavators part #TH898 will fit on the factory crossbars of your 2019 Honda CR-V if the bars extended past the feet of the rack. Otherwise you'd have to go with an aftermarket roof rack like the Rhino Rack part numbers…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The Trailer Hub and Drum Assembly part #AKHD-545-35-K is the correct replacement for an AL-KO 7230. In regards to the braking assemblies, I suggest getting a new pair, the Electric Trailer Brake Kit part #AKEBRK-35-SA. This option will save you some…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...