Roadmaster Rear Anti-Sway Bar 1999 Ford Super Duty

Question

Question:

Hello, Will the Roadmaster 1139-153 Sway bar fit my 1999 Ford Superduty 4WD single rear wheel WITH FIRESTONE RIDE RITE AIRBAGS?

asked by: Thomas C

0

Expert Reply:

Yes, the Roadmaster Rear Anti-Sway Bar, # RM-1139-153 is designed to replace the existing part and designed to work with most aftermarket parts. This is a much stronger sway bar than factory, made with stronger steel than factory and increased to 1-1/4" diameter.

Please see the attached videos for reviews and installation.

expert reply by: Michael R

0

Answer 1

You're absolutely correct. For a 1999 Ford F350 SRW without the factory sway bar, you'd use #RM-1139-153 along with the #RM-590230-00 end link kit.

view full answer...

Answer 2

The correct rear sway bar for your 2000 Ford F-250 is the Roadmaster sway bar part #RM-1139-153 which is a confirmed fit. This will help greatly with handling while towing. We aren't going to have a great suspension support system solution but we…

view full answer...

Answer 3

While I do not know if Freedom Trailers uses the Top Rail Trim for Enclosed Trailer #36279-955, I was able to get some measurements for you. The Top Rail Trim for Enclosed Trailer #36279-955 is 8' long, 2-3/4" wide and 1-1/2" deep. Each…

view full answer...

Answer 4

The Roadmaster Rear Anti-Sway Bar part #RM-1259-109 is a bolt-on component that does not require the rear wheels to be removed. Please note the linked installation instructions for you to review.

view full answer...

Answer 5

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 6

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Roadmaster Rear Anti-Sway Bar 1999 Ford Super Duty

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching