What Wheel Size Requires an Adapter with the Kuat NV Base Bike Rack

Question

Question:

Looking for a 3 bike platform carrier and in interested in the Kuat nv base with and add on. Question is I have a 29er and two other bikes are 24” , will I need the special adaptor to add to make this platform work with the 24” bikes?

asked by: Bobby G

0

Expert Reply:

With the Kuat NV Base 4-Bike Rack part # BA22B-BA02B you have to use the adapter # 016-025-00-00 if the bike wheel is between 20 and 24 inches. Unfortunately this part has been discontinued, and there is not a replacement option.

expert reply by: Jameson C

0

Answer 1

The Kuat NV 2.0 does not include a wheel adapter for 20-14 inch wheels, it was sold separately as part 016-025-00-00, but is no longer available

view full answer...

Answer 2

Verify the tongue weight capacity of your trailer hitch recevier and your Lexus NX200t to make sure you can handle the weight of a fully loaded bike rack. You definitely need a 2 inch Class III hitch on the Lexus which are available so hopefully you…

view full answer...

Answer 3

The Inno Tire Hold #INH142 4-bike rack will accommodate children't bikes with 20 inch wheels or adult bikes with up to 29 inch wheels. Inno tells me that a 33 inch wheelbase bike will just fit on the rack. The Kuat NV 2.0 4-bike, part…

view full answer...

Answer 4

To determine if the Thule T2 Pro XTR part #TH69TX is going to fit your 2017 Jeep Cherokee and allow it to fold up without bumper interference will require you to measure from the center of the hitch pin hole out to the furthest point out on the rear…

view full answer...

Answer 5

The Kuat NV 2.0 #NV22B measures 55-1/8 inches wide overall, folded or unfolded. The height when folded is 25-3/4 inches. When unfolded it is approximately 13 inches tall. When unfolded the rack is 37-3/8 inches front to back. When folded up it is…

view full answer...

Answer 6

The Kuat NV 2.0 #BA22B-BA02B that you referenced can be split and be just a 2 bike rack if you only needed to carry 2 bikes. And then you could easily install the add-on section to make it a 4-bike rack. The add-on section though can not be used as…

view full answer...

Answer 7

This rack comes with locks for both the carrier and the bikes. and they are all keyed alike. The Thule T2 Pro XTR Bike Rack, #TH69TX, kit can be set up to carry 2 or 4 bikes as needed.

view full answer...

Answer 8

Because of the way the Thule T2, #TH9044-TH9046, is designed, there is actually a rise of 4-3/4 inches from the top of the receiver opening on the trailer hitch to the bottom of the nearest platform. The rack angles up even more towards the back and…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…

view full answer...

What Wheel Size Requires an Adapter with the Kuat NV Base Bike Rack

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching