Replacement Pins that Fit Reese 15k Fifth Wheel Hitch Head

Question

Question:

Have older Reese 15K Pro Series hitch. I need correct part number for pins that hold head to body of hitch.. Checked all 1742 you carry and not sure which I need?? Thanks,

asked by: John P

0

Expert Reply:

For the Reese/Pro Series 15k fifth wheel hitch you have the way to order replacement pins for the head of the hitch is with the part # 30583 which does come with additional hardware but it's only way to get just the pins.

expert reply by: Jameson C

0

Answer 1

I believe you are looking for the Replacement Hardware for Reese 16K Fifth Wheel Head Assembly and Head Support #30583. These bolts mount the head cross assembly to the legs and are only available in the kit.

view full answer...

Answer 2

Yes, I went out to our warehouse and checked the Replacement Hardware for Reese 16K Fifth Wheel Head Assembly and Head Support part #30583. It does indeed come with four 1/2" hex head bolts and four 1/2" nyloc nuts which will be…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 7

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 8

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 9

The B and W Patriot slider is the only hitch unfortunately that can't be adapted to fit the OEM rails of your 2024 Ram 2500 as none of the adapters can work with it. So Mike what that means is that no matter how you slice it...it's time for a…

view full answer...

Answer 10

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 11

Yes, you are going to also need the Demco Autoslide Capture Plates for Trailair Rota-Flex Pin Boxes #DM6171 when using the Demco Autoslide 5th Wheel Trailer Hitch w/ Slider #DM8550040 with your Road Armor pin box. For a suspension enhancement I…

view full answer...

Answer 12

I checked with GEN-Y and they were able to get me the distance from the top bolt hole of the #GY48GR down to the bottom of the coupler which you can see in the attached picture as well as a few other dimensions. It's 23.8 inches. It does not come…

view full answer...

Replacement Pins that Fit Reese 15k Fifth Wheel Hitch Head

Product Page this Question was Asked From

Continue Researching