Wiring Adapter For 2021 Toyota Tacoma To Install Tekonsha Primus IQ Trailer Brake Controller

Question

Question:

I have a new 2021 Tacoma and I want to install a Tekonsha 90160 Brake controller. I need a wiring harness. Can you help me?

asked by: Garry K

0

Expert Reply:

Sure, I can give you a hand, as we do in fact have the correct wiring harness for your 2021 Toyota Tacoma so you can install the Tekonsha Primus IQ Trailer Brake Controller # TK90160.

All you need is the Tekonsha Custom Wiring Adapter for Trailer Brake Controllers # 3031-P.

One end will plug into the Primus and the other end will plug into your Tacoma's factory tow package port and you're set. I have added some links below to video reviews for you to check out as well if you'd like.

expert reply by: Kyle S

0

Answer 1

When it comes to your 2021 Toyota Tacoma I recommend The Redarc Tow-Pro Elite Trailer Brake Controller #RED44FR. It is for up to 1 to 3 axles and its completely hidden under the dash except for the knob that controls how much power goes to the…

view full answer...

Answer 2

The brake controller install harness part #3031-P is the correct install harness for a Tekonsha Primus brake controller part #TK90160 in a 2023 Toyota Tacoma.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...