Which Curt Wiring Harness for a 2020 Ford Edge SE or SEL

Question

Question:

could you tell me the Curt part # for A #C89FR

asked by: Darrel S

0

Expert Reply:

The # C89FR has the manufacturer's part number 56436, which is the CURT T-Connector Vehicle Wiring Harness with 4 Pole Trailer Connector. This harness is a confirmed fit on your 2020 Ford Edge as long as you have either the SE or SEL trim package.

I've also linked the installation video of this part for you to check out, as well.

expert reply by: Erik B

0

Answer 1

I believe I have a solution that would allow you to lower your Yakima DoubleDown, but the Roadmaster Hi/Low adapters are not rated for any use besides flat towing. Check out the Curt Hitch Adapter #D-192. You could flip this product so that the…

view full answer...

Answer 2

since 2015, Ford has changed their wiring in their trucks and it has been causing several different issues including the problem you are having with installing the LED lights. Resistors like the LED Kit, part #DI34ZR are not always needed and it is…

view full answer...

Answer 3

Because it is only for a 2022 Hyundai Palisade that has the factory tow package, you do not need to route any wires whatsoever to add the Curt 7-way that fits, which is the following part number: - Curt T-Connector Vehicle Wiring Harness for Factory…

view full answer...

Answer 4

You may not even need load resistors to switch to LED lights. The best thing to do is to try the lights without load resistors first. No need to purchase something you may not need until you know need it. Load resistors such as #DI34ZR dissipate heat…

view full answer...

Answer 5

We do not have a 4-way to 4-way adapter with the diodes that stop the hyper flashing. You can install load resistors like part #DI34ZR. You would install the load resistors on the affected circuits. I have attached a drawing that shows how the…

view full answer...

Answer 6

It is not uncommon for LED lights to not draw enough power for the 4-way or 7-way to work properly. If the #H01540 lights are not working when plugged into your 2023 Ford Transit, that is likely the cause. If you have a 7-way, you could use the 7-Way…

view full answer...

Answer 7

You could use the LED kit part #98174LED to add the lights and wiring to your Kuat NV and then use the bracket #BK70BB and you'd be set. You'd have to attach the brackets to the bike rack.

view full answer...

Answer 8

You will wire a load resistor into the wiring of each light socket that has an LED bulb and flashes. So basically you will need to wire a load resistor into any bulb that blinks or has a dual intensity feature that lights up when the brakes,…

view full answer...

Answer 9

I wish it was that simple but putting a load resistor on the brake output circuit of your 7-way would not prevent the issue you are having. The error message is due to lower amperage draw of the trailer lighting circuits and not the trailer brakes.

view full answer...

Answer 10

The information we have for your 2006 Ford Explorer is that if it does not come with a 7-way the brake controller wiring isn't complete and and if you tried to plug in a controller the circuits wouldn't be active. Only way we can recommend is…

view full answer...

Answer 11

LED lights draw less power than the incandescent lights you are replacing which can cause issues. You will want to use load resistors like Load Resistor Kit for LED #DI34ZR on each light you are replacing.

view full answer...

Answer 12

Yes. High-efficiency LED type trailer lighting pulls much lower current than standard incandescent lights. This can cause odd behavior from the wiring harness but there's a simple solution to this issue. You can install a load resistor at each…

view full answer...

Which Curt Wiring Harness for a 2020 Ford Edge SE or SEL

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching