How Do I Install Load Resistors for the LED Lights on my 2007 Dodge 3500 Flatbed
Question:
I have a 2007 Dodge 3500. I have a CM Flatbed on the abck with 4 3x5 LED tail lights I ordered. When I installed them It threw the light out chime/error code when I brake and when I use turn signals. I ordered 4 Resisters for Superbright LED.com. I am wondering if I just need to hook 1 to left turn and 1 to left brake and them same on right side to remove the error code.... Also I have heard about people wiring in a normal light under the bed so there is resistance on the computer... I am just wanting some advise. Thank you
asked by: Carson B
Expert Reply:
You will wire a load resistor into the wiring of each light socket that has an LED bulb and flashes. So basically you will need to wire a load resistor into any bulb that blinks or has a dual intensity feature that lights up when the brakes, blinkers, or emergency flashers are operated.
To do this correctly, you will need to wire the load resistor on the positive wire and then either ground it to the ground wire of the bulb, or to a good frame ground. You will need to do this for all of the LED bulbs that blink with the blinkers or flashers, and that illuminate brighter when the brake is applied.
Installing hidden lights on the circuit will also clear up the problem too. You would have to install a bulb on every circuit though, and if the bulb blows the lights will not work properly and you will see error codes again.
Product Page this Question was Asked From
Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2
- Accessories and Parts
- Trailer Lights
- Load-Resistor Kit
- Diamond
more information >
Continue Researching
- Shop: Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2
- Video: Review of Diamond Lights - Load Resistors - DI34ZR
- Shop: Optronics Load Resistor for LED Lights - Male PL-3 Plug and Female PL-3 Plug - Qty 1
- Q&A: Solution for Rapid Signal Flashing on Utility Bed with LED Lights
- Shop: Trailer Wiring
- Shop: Replacement Gas Strut for Roadmaster Tow Defender - Qty 1
- Shop: Towing Mirrors
- Shop: Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent - White - Wedge Shape - Plastic
- Shop: Electric Jack w/ Footplate - Drop Leg - A-Frame - 25-1/8" Lift - 3,500 lbs - White
- Shop: Suspension Enhancement
- Shop: SuperSprings SuperSway Stops - Qty 4
- Shop: 7-Way Trailer Adapter for Towing Trailers with LED Lights
- Q&A: Correcting Hyperflashing Taillights in 2009 BMW X5
- Article: REDARC Tow-Pro Liberty vs Tow-Pro Elite
- Q&A: Correcting Hyperflashing After Installation LED Taillights on 2004 Dodge Ram 3500
- Video: Ventline Ventadome Replacement Vent Installation
- Q&A: Trailer Lights Not Working Using 4- to 7-Way Adapter on a 2012 Mercedes GL450
- Search Results: load resistor
- Search Results: aledrst2b
- Video: Optronics Trailer Lights - Utility Lights - BUL78CB Review
- Article: Brake Controller Installation on a Ford Full-Size Van
- Article: Trailer Wiring Diagrams
- Search Results: jack wheel
- Q&A: Installing LED Light Bulb Load Resistor Kit
- Q&A: Trailer Running Lights Slowly Pulse On and Off and Rear Tail Lights Not Working w/Mercedes Sprinter
- Q&A: Load Resistor For Correcting LED Trailer Running Lights That Light Dim When Vehicle Is Turned Off
- Video: Optronics Load Resistor for LED Lights Installation
- Shop: Vehicle Tow Bar Wiring
- Search Results: led rv tail lights
- Video: Optronics Trailer Lights - Clearance Lights - MCL66AB Review