Snatch Block to Use with Bulldog Winch part # BDW15020

Question

Question:

Bulldog Winch Trailer Winch - Synthetic Rope - Hawse Fairlead - 4,400 lbs Item # BDW15020 Looking to purchase Snatch Block to use with winch. Any recommendations for which one would work best.

asked by: Lester H

0

Expert Reply:

The Bulldog Winch Snatch Block # BDW20005 would work great with the Bulldog Winch part # BDW15020 as it has more than enough capacity and was designed for use with synthetic rope like the winch has.

expert reply by: Jameson C

0

Answer 1

3/16 inch diameter wire rope is a standard winch cable size like what the ComeUp Snatch Block part #CU881080 was designed to work with so this would work great.

view full answer...

Answer 2

A Superwinch LT2500 has a 2500 lb line pull capacity. For a rolling load like a car with fully inflated tires, a winch with a capacity equal to the weight of the vehicle, in your case 4000 lbs is recommended. This means that your winch has about half…

view full answer...

Answer 3

We have pulley blocks like the #BDW20023 that could be used in your application but you'd have to come up with a way to mount them since we don't have setup designed for your application.

view full answer...

Answer 4

Since you are getting a car hauler trailer and will be pulling vehicles onto it that means you will have rolling loads. A rolling load is much easier to move than a static load so you do not have to have a high capacity winch. When winching a rolling…

view full answer...

Answer 5

You can use a pulley block like part #BDW20005, to pull your car on to a trailer with the winch being offset. You will want to make sure the winch is well secured for safety. This pulley block has a capacity of 17,000 lbs break strength and is…

view full answer...

Answer 6

The Superwinch #1120210 LT2000 you referenced would be perfect for your needs. According to my calculations, the ramps you are using have a bit more than a 40 percent grade. According to the table shown in the FAQ article I have linked you to, the…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Snatch Block to Use with Bulldog Winch part # BDW15020

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching