Curt RockerBall for 2015 BMW 328xi Wagon

Question

Question:

I would like to pull my Yamaha Waverunner behind it. I have a 1 1/4inch hitch. I need a 2inch ball. Will this work?

asked by: Jeff B

0

Expert Reply:

Yes, the Curt RockerBall # C94CR meets your needs of a 2" Hitch Ball. This has a 3/4" Diameter Shank that is 2-1/8 Inch in length.

If you need a drawbar for your 1-1/4" hitch I suggest the Curt Class II Drawbar # C45521.

expert reply by: Michael R

0

Answer 1

The Furrion RV Stereo #DV3300SBL can be paired to your smartphone by completing the following steps: 1. Activate Bluetooth mode on your mobile device. Then press the Bluetooth button on the front panel of DV3300S to enter pairing mode. 2. When…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You're correct. The repalcement for your existing B12EA-22 brake would be #AKEBRK-7R-SA for the right side and #AKEBRK-7L-SA for the left.

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 10

The TireMinder i10 TPMS #TM38FR refreshes every 6 seconds. You will get a visual and audible alert when the monitor receives the signal from your tire sensor is either below your pressure or the temperature exceeds the maximum setting.

view full answer...

Answer 11

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 12

You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…

view full answer...