What Type of Cable Connector is the Rear View Safety Adapter Cord

Question

Question:

will this cable connector fit into my female backup camera cable, if not which one do you recommend.

asked by: Frank

0

Expert Reply:

Assuming that you've got an RVS (or similar) backup camera that connects to a monitor via RCA cables and has a plug with a 5 pin female plug then the # RVS-RCA5-M will work for you. I've linked a photo of what this 5 pin plug looks like for you to reference to your female plug.

If you've got a different system than the RVS, or your plug looks different and can provide a photo just let me know and I can see if we have something compatible.

expert reply by: Erik B

0

RVS 5 Pin Plug
(click to enlarge)

Answer 1

To connect the JRV9000R to your old VR187 wiring you'll need the ASA Electronics CRT to LCD Monitor Cable Adapter Item #31100041. For JRV9000R I recommend the Voyager Rear Camera with LED Low Light Assist - Black Item #VCMS17B and the adapter…

view full answer...

Answer 2

I have attached for you below the pairing procedure for the Voyager WiSight Wireless RV Backup Camera System part #ASA84YR. Please note, a mistake I have made in the past was applying power to the camera too soon, this cannot be done until the…

view full answer...

Answer 3

I may have a solution for you, but it's actually not the bed rail system that's going to cause issues; it's the tonneau cover you've got on your 2018 Toyota Tundra. Because that tonneau sits above the rails and mounts where the ladder…

view full answer...

Answer 4

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 7

There is a suggested and common method for 6 function trailer wiring. You will have the following functions: Right Turn, Left Turn, Ground, Tail/marker, Brake, Battery. I have included a help article on trailer wiring that includes a diagram and…

view full answer...

Answer 8

Since you have a Dometic AC unit the best option to replace it from Advent would be the part #ACDOM135 which was designed for this exact situation and would allow you an easy install since the electronics would plug right in.

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 11

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

What Type of Cable Connector is the Rear View Safety Adapter Cord

Product Page this Question was Asked From

Continue Researching