Can Two Self Centering Keel Rollers Install on Boat Trailer

Question

Question:

DOES IT MAKE SENSE TO INSTALL TWO SELF CENTERING KEEL ROLLERS?

asked by: Wm. Y

0

Expert Reply:

There certainly wouldn't be any negative effects from using two self-centering keel rollers like the CE Smith Keel Roller part # CE29505 although some might say it's redundant.

expert reply by: Jameson C

0

Answer 1

For starters, in order to use the CE Smith Self Centering Keel Roller for Boat Trailers part #CE29505 on your boat trailer you will also need to use the CE Smith Panel Bracket for 12" Boat Trailer Rollers part #CE10305G and the Roller Shaft with…

view full answer...

Answer 2

The self centering roller part #CE29505 does not come with a mounting bracket but for that we have the #CE10305G for a bracket and for a roller #CE10727A which includes pal nuts.

view full answer...

Answer 3

Thanks for the photo. It does indeed look like you need to move your keel rollers up towards the bottom of the boat until they are touching but not supporting the full weight. Therefore, marking the bracket when the rollers are flush to the bottom…

view full answer...

Answer 4

The keel roller will help to center your boat as the wobble rollers you have allow the boat to sit slightly to one side or the other. We do offer the CE Smith Keel Roller #CE29505 which has a self centering design to help guide your boat to the…

view full answer...

Answer 5

The LM67000LA is a Timken part number for a bearing cone with a 1.250" I.D. and a 2.328" O.D. This is the same as our bearing part #LM67048. The LM67010 is a Timken part number for a race with a 2.328" O.D. that matches our part…

view full answer...

Answer 6

Dico was bought out by Titan who now offers 5-on 4-1/2 idler hub #DX22XR. This hub is rated for 2500-lb axles and includes bearings, races, grease seal, grease cap, and lug nuts. You can be assured it will fit the trailer spindle as long as the…

view full answer...

Answer 7

I have a potential alternate option, but unfortunately, the Titan Trailer Hub Assembly for 2,500-lb Axles - 5 on 4-1/2 - Cast T1721400042 is no longer available from the manufacturer. As this uses an uncommon combination of inner and outer bearings,…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Can Two Self Centering Keel Rollers Install on Boat Trailer

Product Page this Question was Asked From

Continue Researching