Marine Grade Swivel Jack Certification

Question

Question:

Are there any certifications in the US or Europe for this jack. Round Swivel Marine Jack w/ Dual Wheel - Bolt On - Zinc - Sidewind - 10-3/8 Travel - 1.5K Item # MJ-1500B-DWL Thank you

asked by: Dan L

1

Helpful Expert Reply:

There are currently no established standards for marine jacks like # MJ-1500B-DWL in the US. Europe does have the "CE" standard, but our jacks have not gone through that process.

With that being said, we do fully test our jack design to insure that they meet (and in most cases) exceed the ratings that we assign to them. We also do periodic random testing from our production to ensure quality and meeting of the capacity limits.

The Round Swivel Marine Jack w/ Dual Wheel # MJ-1500B-DWL is a bolt on trailers jack that is designed to lift 1,500 lbs. It is certified as a marine jack because of it's zinc finish. This is rust resistant and is okay to be submerged in water when loading and unloading your boat.

expert reply by: Adam E

1

Answer 1

While we do have some great U.S.A.-made boat trailer jacks, the etrailer Round Swivel Marine Jack #MJ-1500B-DWL is manufactured in China. However, for a super close U.S.A.-made model, I recommend the Dutton-Lainson Swivel Marine Jack #DL67MR. This…

view full answer...

Answer 2

The mounting plate on the ARK Removable Extreme Off-Road Swing-Up Trailer Jack #ARK57FR is 5-1/2" wide and 7-1/2" tall. It is designed with several bolt hole patterns(see image) to fit trailer tongues from 2-6" tall.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...