Availability of Just Brackets and Hardware for Reese Rail Kit 5003-6008

Question

Question:

I wanted to buy the Fifth Wheel Trailer Hitch Custom Installation Kit with Brackets and Rails - Ford Super Duty 1999-04 Item # 50043-6008. I have a 200 F350 and this is confirmed to fit. I already have rails but lost the hardware. Do you sell this kit minus the rails?

asked by: Ryan

0

Expert Reply:

For everything minus the rails of the kit you have now all you'd need is the part # 50043 which is the brackets and hardware needed.

expert reply by: Jameson C

0

Answer 1

Since you already have the rails for your fifth-wheel hitch you will not need to purchase the rails again so you can use the Fifth Wheel Trailer Hitch Custom Installation Brackets - Ford Super Duty Trucks, item #50043, for your installation. With…

view full answer...

Answer 2

The bracket kit part #50043 does not include the hardware that attaches the rails. It only comes with hardware to attach the brackets to the truck frame. So you would also need the bolt kit part #RP58430 which is the hardware you are looking for.

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 5

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Availability of Just Brackets and Hardware for Reese Rail Kit 5003-6008

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching