How To Attach a Westin Fey Diamondstep Rear Bumper To Vehicle With No Custom Brackets

Question

Question:

Hi there, I am looking for an off road style rear bumper for a 2000 ford explorer similar to part no. 61000. Do you have any bumpers for this or similar vehicles? many that i had found in your website so far say they are not a direct fit. if there is not an exact fit, do you offer at that are about the right size that could possibly be made to work with some modifications? please let me know. thank you,

asked by: Colin L

1

Helpful Expert Reply:

In order to affix an aftermarket bumper to a vehicle in which a custom bumper is not available for you'll need to measure the length of the bumper and then compare this to the list below for the best fit match.

- Westin Fey Diamondstep Rear Bumper # 65000: 64-1/2"
- Westin Fey Diamondstep Rear Bumper # 63000: 64"
- Westin Fey Diamondstep Rear Bumper # 61000: 61-1/2"

Once you have the best match as far as length goes, you'll need to make up a custom set of brackets or modify the existing in order to make work. There are no custom options for a 2000 Ford Explorer. The Installation Kit for Westin Diamondstep, Surestep and Surestep Deluxe XLT Bumpers part # 92230 which would require modifying would be another option.

expert reply by: Conner L

1

Answer 1

Per Westin-Fey, the correct mounting kit for to mount the Westin Fey Diamondstep Rear Bumper #61000 to your 1985 Nissan 720 would be the Custom Installation Kit for Westin Diamondstep and Surestep Bumpers #95500.

view full answer...

Answer 2

I recommend installing our etrailer Trailer Hitch Receiver #e29AR on your 2008 Ford Ranger 4x4 with the 4.0L 6 cylinder engine. The frame mounted receiver may require the drilling of 2 additional holes as Ford did not drill these holes in every Ford…

view full answer...

Answer 3

It is difficult to identify what hitch fits just by looking at the holes in the frame. However, I can tell you that the Curt Trailer Hitch Receiver #13138 is confirmed to fit your 2004 Ford Ranger Edge. This is a Class III hitch with a 2"…

view full answer...

Answer 4

I spoke with my contact at Curt and he stated that trailer hitch #13138 does fit the 2002 Ford Ranger Edge flare side. I have included a link to the installation details for you. If you plan on doing some towing, I recommend the etrailer Ball Mount…

view full answer...

Answer 5

For your 2011 Ford E-250 we have the Westin Fey Diamondstep Rear Bumper which is offered in black part #20107, silver part #20105, and chrome part #21105. These options are all custom fit and they come with all the brackets and hardware needed to…

view full answer...

Answer 6

I did take a look at what we have for your Sportrack Hitch N' Drive 700 Deluxe Series, and while we do offer the Locking Knob with Bolt for SportRack Single-Arm, Hitch-Mounted Bike Carriers #SR0018 which does fit your Hitch N' Load bike rack,…

view full answer...

Answer 7

The Swagman Original Bike Rack part #S64400 that you referenced has been confirmed to work at the back of a camper, RV, fifth wheel, or trailer so it would work well at the back of your RV. I attached a review video for this bike rack for you to…

view full answer...

Answer 8

The Tulga T10 D2 5th Wheel Hitch is more for semi-tractor applications and has a pretty big draw-back in that you cannot adjust the hitch head height which is critical for fifth wheel towing because you need to be as level as possible or you will…

view full answer...

Answer 9

The B and W Turnoverball hitches have an adjustment built into them to allow for varying heights. If you check out the picture I attached you'll see that you the socket post is adjustable to allow it to fit your setup. It's also in the…

view full answer...

Answer 10

Yes, the Dexter hub part #8-287-14UC1 can have grease used in it instead of oil. The only difference is the seal which an oil seal works just fine with grease.

view full answer...

Answer 11

Sure can; there are a couple parts you'll need to add a 7-way to your 2023 Chevy Bolt EUV, which are the following: - Tail Light Converter w/ 4-Way Flat Trailer Connector #C59496 - Universal Installation Kit for Trailer Brake Controller #ETBC7…

view full answer...

Answer 12

Before installing a brake controller to your 2006 Ford Van, you need to have a 4-way and a 7-way wiring harness installed. First, you need to install the 4-way. If you need a 4-way harness, I recommend the Hopkins Plug-In Simple Wiring Harness -…

view full answer...