Measurement From Center Pin Hole to Shank of Curt Hitch Extender C45791

Question

Question:

what is the depth from the extension side outside center of hole rearward to where the weld is inside the tube?

asked by: John

0

Expert Reply:

I believe I know the measurement you are referring to, which is just from the center of the pin hole of the extension back to the weld where the shank portion begins of the Curt Hitch Extender for 2" Hitch Receivers # C45791.

That measurement, from pin hole to shank, is 5 inches. I have added links to video reviews for you to check out as well of this extender.

expert reply by: Kyle S

0

click to enlarge

Answer 1

In regards to the Adjustable Width Trailer Hitch Receiver for RVs part #13703, the brackets have a built-in offset so you can install them in a manor which pushes the crosstube further out towards the bumper. This will help reduce clearance issues…

view full answer...

Answer 2

I spoke to Yakima about the StraightShot #Y69VR extender, but they have only tested this with Yakima accessories. Due to this, it doesn't have a listed tongue weight. With that being said, the Yakima bike racks and other accessories are going to…

view full answer...

Answer 3

What a cool set up! Bad news on the extender front none of my extenders are rated for anything close to that. I totally get the reasoning and would also want to keep them separated. As another option you can use the Curt Multi-Ball Adjustable Ball…

view full answer...

Answer 4

There is no torque spec for the Malone Anti-Rattle HitchLock System part #MPG908. In regards to tightening, you simply need to collapse the split-lock washer and that will be good.

view full answer...

Answer 5

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 6

We may have a grease seal that will work in your application however, my research had conflicting measurements for the Hadco 3122 that you referenced. I contacted my technical contact at Redline to verify that the Redline Grease Seal #1105-100-031…

view full answer...

Answer 7

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 8

We have a really great kit that comes with everything you'd need to convert your 2021 Vanleigh Pinecrest 335RLP from tandem 6k drum brakes to electric over hydraulic disc brakes with the HydraStar Disc Brake Kit w/ Actuator for Triple Axle…

view full answer...

Answer 9

I have attached for you below the recommended procedure to flat-tow a 2019 Jeep Cherokee Trailhawk per the owner's manual. The last step states to place the ignition in the off position so that is what I must recommend. 1. Bring the vehicle to a…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

Hi Robert; hopefully your Roadmaster tow bar is one that attaches to direct-connect base plates as opposed to crossbar base plates; for example the 8,000 lb Roadmaster Sterling would be optimal. Assuming that, here is what you need to flat tow your…

view full answer...

Answer 12

Any type of hitch adapter or extender will have the unavoidable side-effect of causing a loss of about half of your hitch's rated capacity, both its tongue weight (TW) and it's gross towing weight (GTW). Hidden Hitch extender #HE18 and Curt…

view full answer...

Measurement From Center Pin Hole to Shank of Curt Hitch Extender C45791

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching