Why Does JTs Strongarm System Come with a Total of 6 Bars

Question

Question:

The kit comes with 6 bars, how do attach 2 bars each foot on the front pads on an electric stabilizer from Lippert? The directions show 1 per foot for a total of 4 but the kit comes with 6 bars.

asked by: Ken H

0

Expert Reply:

Two of the bars that come with the JT's Strong Arm Jack Stabilizer Kit for Travel Trailers # LC191025 install on the front landing gear legs like you can see in the attached picture and install video link on this page and the other two install on the stabilizer jacks towards the rear of the vehicle.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The other end of the JT's Strongarm part #LC191023 has a wider lug spacing to allow the #LC191023 to install into. You are trying to install the kit on the end that is narrower.

view full answer...

Answer 2

Since you have electric stabilizers on your RV you would only use 4 of the arms that come with the part #LC191025. If you check out the install instructions link I attached you can see that your setup is shown in figure 3.

view full answer...

Answer 3

For your 2019 Jayco Jay Flight 32BHDS with heated underbelly, the JT's Strong Arm Jack Stabilizer Kit for Travel Trailers #LC191025 will fit and give you the stabilization you are seeking. The enclosed underbelly will not hinder the fit in…

view full answer...

Answer 4

I went our to the warehouse to measure the eye to eye distance on the arms of the JT's Strong Arm Jack Stabilizer Travel Trailer Kit #LC191025. From the center of one eye to the center of the other it was exactly 26 inches.

view full answer...

Answer 5

I went out to the warehouse to measure the length of the arms when extended for the JT's Strong Arm Jack Stabilizer Kit #LC191025. From the center of the hole on one end to the center of the hole on the other end it measures 46 inches…

view full answer...

Answer 6

There isn't a minimum distance apart that the JT's Strong Arm Jack Stabilizer Kit for Travel Trailers part #LC191025 must be located. The instructions state the following in regards to positioning. - Locate a cross-member rearward of…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 9

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 10

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 11

Since the issue appears to be on the vehicle side for your 2017 Toyota Tacoma, I recommend first checking the connector itself. Look to see if there is any dirt or corrosion built up inside the connector that may preventing a solid connection with…

view full answer...

Answer 12

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Why Does JTs Strongarm System Come with a Total of 6 Bars

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching