Replacement Shanks for Fastway Weight Distribution for Use in 2-1/2 inch Trailer Hitch

Question

Question:

I have a fast way e2 reunion WD hitch o use to tow a 2020 30’ airstream. I upgraded to a Ram 2500 Crew 6’4”bed 4x4 and need a new shank. I am not sure which I need and I want to use the 2-1/2 receiver.

asked by: Steven M

0

Expert Reply:

We have a few options for replacement weight distribution shanks that fit both the Fastway weight distribution system you have as well as the 2-1/2 inch hitch on your vehicle. We have the # EQ90-02-4700 which can do up to a 3 inch drop, # EQ94FR which can do up to a 9 inch drop, and # EQ90-02-4900 for up to 6 inch drop.

expert reply by: Jameson C

0

Answer 1

Looks like you are in need of a drop shank for your weight distribution system to allow your trailer to be towed level. The Equalizer Shank part #EQ90-02-4400 can do a drop of up to 9 inches so it would work well for you as it looks like you need…

view full answer...

Answer 2

Since your truck has a lift, and without a lift it sits up pretty high I would recommend a shank that fits the 2.5 inch hitch size with a bit more drop in the shank like the #EQ90-02-4900 which can do a drop of up to 6 inches or the part #EQ94FR…

view full answer...

Answer 3

The minimum drop of the Equal-i-zer Weight Distribution Shank part #EQ94FR is 4".

view full answer...

Answer 4

Sounds like you just need a larger drop weight distribution shank for your WD system. This is a very common problem with newer vehicles as they make them taller and taller. The part #EQ90-02-4400 that you referenced would do a great job with this as…

view full answer...

Answer 5

The Equal-i-zer Weight Distribution Shank part #EQ94FR is what I recommend using for a 2-1/2" hitch where extra drop is needed. It offers up to 9" drop which should be plenty for most truck and trailers combos. It's cross-compatible so…

view full answer...

Answer 6

The Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 10" Rise/6" Drop - 600 to 1,600 lbs TW #EQ90-02-4900 is a great option for a hitch with a 2-1/2 inch receiver and it will step down to fit the e2 system you have perfectly. This shank…

view full answer...

Answer 7

Between using a reducer sleeve and upgrading your weight distribution shank, I recommend going with a weight distribution shank designed to fit the 2-1/2 inch hitch receiver on your 2015 Ram 2500HD. Using a 2/1/2 inch shank, like #EQ90-02-4800, for…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

That sounds right to me Travis, but while you have everything pulled out it wouldn't hurt to re-measure and double-check. The height shouldn't have changed and everything should essentially go as you've described, but If it were me…

view full answer...