Is There a Red and Amber 2-Wire LED Trailer Light With Mounting Bracket

Question

Question:

Product: PE89BR or similar LED I am looking for a compatible base for this lamp, I would also like for it to have 2 wires so that I dont need to rely on a chassis ground. Thank you.

asked by: Robert C

0

Expert Reply:

We do have exactly what you are looking for, which is a red and amber LED 2-wire trailer light that has a bracket.

What you need is the LED Trailer Fender Light with Mounting Bracket # OPT49FR.

This is a surface-mounted light that comes with its own bracket and has two wires, one for power and one for ground so you don't need to rely on the chassis ground.

expert reply by: Kyle S

0

Answer 1

Thanks for the pictures of your lights! Based on that you'd want the part #328-003-19R for red lights that match what you have and #328-003-19A for amber. These ground through a white wire but you can run that white wire's ring terminal to…

view full answer...

Answer 2

Thank you for the pictures! We do not have an exact replacement but we have something extremely close. It is the LED Trailer Fender Light item #PE89BR. This light measures 3-7/8" long x 1-1/4" tall x 7/8" deep. It is a dual-face LED…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...