Bolt Hole Pattern of Replacement Bolt-On Mounting Kit

Question

Question:

What are the dimensions of the hole pattern on the “inside” of the adapter? In other words, the 4 bolt holes that you have not already provided dimensions for. I need to convert from the mounting plate on a load rite trailer picture to a standard hole pattern on a knot jack stand. The hole pattern on the mounting plate is 3 1/8” left/right and 3” up down.

asked by: Matt O

0

Expert Reply:

The bolt holes of the Replacement Bolt-On Mounting Kit for Fulton XP Series Jacks # F500349 measure 3" apart on center in order to line up with the Jack Mounting Bracket # P9012-00.

expert reply by: Kyle S

0

Answer 1

Fulton bolt-through trailer jack #F1411300301 is the only Fulton jack that mounts using that 1 center bolt. Since your old jack was a Fulton it must either be this same jack or an earlier model but they use the same mount. The mount in question and…

view full answer...

Answer 2

The picture you submitted looks like the mount of a Fulton XP jack part #FXP15W. Which if you are looking for a replacement mount you'd want the part #F500349.

view full answer...

Answer 3

In regards to mounting the Fulton Bolt-Thru Swivel Marine Jack part #F1411300301 you'll need a mounting kit like the Bolt-On Mounting Kit for Fulton part #F500349 which contains the mount and the center bolt, nut, and tapered spacer. The only…

view full answer...

Answer 4

I contacted our representative at Fulton about the Fulton Round, Snap-Ring Swivel Marine Jack, part #FTJ120W0301. The inner diameter of the mounting hole is 2-1/2 inches. He informed me that up to a few years ago the Fulton jacks were made in…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 8

The 8-14.5 tires are an older metric size no longer used today. Therefore, you would need to replace these along with the wheels in order to update them. In order to see if we have any options for you, we'd first need to determine the bolt…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

I would be happy to! The bottom of the foot to the center of the pipe mount is 10-1/2" when retracted and 24-1/2" when fully extended on the Trailer Valet JXS Trailer Jack w/ Footplate and Drill Powered Option item #TV64FR. Sorry I do not…

view full answer...

Answer 11

According to our research the Fulton Round, Snap-Ring Swivel Marine Jack #FTJ120W0301 will fit as a replacement for your Shelby 5756 boat trailer jack. It will allow you to keep the same bracket that is currently welded-on. You basically need to open…

view full answer...

Bolt Hole Pattern of Replacement Bolt-On Mounting Kit

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching