Will the Strait-Line Weight Distribution System Work With Gen-Y Torsion Weight Distribution Shank

Question

Question:

Already have the geny torsion weight distribution shank, can I just attach the shankless Reese straight Line wdh kit to it? Any issues?

asked by: Matthew M

0

Expert Reply:

Yes, the Strait-Line Weight Distribution (No Shank) part # RP66074 will be directly compatible with the Gen-Y Torsion Weight Distribution Shank part # GY54FR.

expert reply by: Conner L

0

Answer 1

A Gen-Y Torsion ball mount like #325-GH-1024 can be used with a Curt MV weight distribution system. You will put the weight distribution system shank in one of the stacked receivers and that will give you a smooth ride and still give you the…

view full answer...

Answer 2

One option that might help is the Gen-Y Torsion 2-Ball Mount w/ Stacked Receivers #325-GH-1024. This is a cushioned ball mount setup that basically gives the ball mount connection of the trailer suspension. This uses torsion springs to vertically…

view full answer...

Answer 3

If you want to just add on some sort of extension you can use Safety Chain Quick Link #C82932 which has a working load limit of 3300-lbs. This will give you about 3-inches additional length. Ideally trailer safety chains will be one continuous chain,…

view full answer...

Answer 4

It looks like your 2019 Lance 2465 travel trailer tops out at 6,830 lbs. The Strait-Line Weight Distribution w/ Sway Control item #RP66074 will work for you trailer. It has a tongue weight range of 600 lbs - 1,200 lbs which is perfect for your Lance…

view full answer...

Answer 5

To use your Strait-Line Weight Distribution w/ Sway Control - No Shank - Trunnion Bar - 12K GTW, 1,200 lbs TW #RP66074 in the 2-1/2" trailer hitch receiver your 2018 Ford F-250 has you will need the Curt Weight Distribution Shank for 2-1/2"…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. The Replacement Head for Blue Ox SwayPro Weight Distribution Systems part #BXW4011 is for…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

Hey Mike I checked with Westin and I can confirm that the Westin HDX Xtreme Nerf Bars item #W45XV do indeed fit the 2021 Ram 1500 Quad Cab. The instructions on their website say crew cab as well. This is pretty common amongst aftermarket part…

view full answer...

Answer 12

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Will the Strait-Line Weight Distribution System Work With Gen-Y Torsion Weight Distribution Shank

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching