Replacement Actuator for 1006 Pop Up with Frozen Atwood

Question

Question:

I understand Atwood no longer available. What is the best way to repair / replace siezed master cylinder on a 2006 Jayco 1006 pop up trailerDe

asked by: Dennis O

0

Expert Reply:

Since the Atwood parts are all gone like you noticed you'll need to have your current actuator removed and have a new one like the Titan # T43397007K you referenced welded in place of it. I attached a picture we got from a customer that went through basically the same thing.

expert reply by: Jameson C

0

click to enlarge

Answer 1

That looks like an older Atwood coupler. Which I am not surprised it isn't working as it's the most problematic actuator that we have experience with. Most popular coupler we have that would work as a replacement would be the Titan actuator…

view full answer...

Answer 2

It sounds like you have a switch that has 3 positions, up, down, and off, similar to #PK34312. For each position that requires power there will be an input from the 12 volt power source and an output from the switch to the device it runs. You will…

view full answer...

Answer 3

Your Tie Down Model 66 can easily be replaced by one of our actuators. The Titan part #T43397007K would be a great drum brake option that has a 7,000 lb capacity and can fit 2 inch or 1-7/8 inch hitch balls.

view full answer...

Answer 4

The Demco actuators and the Titan brake actuator item #T43397007K you were looking at are all industry standard to fit over a channel tongue that is up to 3" wide. I have attached a pic of the Titan actuator installed inside the channel and…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 8

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

Thank you for the pictures of your coupler. You are going to need to replace your entire surge actuator coupler as the A-50 is obsolete and we do not have any parts to repair it. We have the Dexter DX7.5L A-60 Brake Actuator #DX73FR which you can…

view full answer...

Answer 11

It sounds like you have free backing braking assemblies on your trailer so a lockout at the trailer coupler is not needed. In order to replace the Atwood Surge Brake Actuator 82541, I recommend using the Titan Leverlock Brake Actuator part…

view full answer...

Answer 12

Thank you for the image. It appears you will need either the Demco Channel Tongue Trailer Coupler #DM13203-95 or #DM16080-95. Both of these couplers have a zinc coating for increased corrosion resistance and fit on a standard 3" wide channel…

view full answer...

Replacement Actuator for 1006 Pop Up with Frozen Atwood

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching