Which Torklift Hitch/Replacement Hardware Fits 2014 Ram 3500

Question

Question:

i talked with torklift on the phone and they gave me a part number of D1104. I would like to verify what it is on your website.

asked by: Scott D

0

Expert Reply:

For your 2014 Ram 3500 with a factory hitch the Torklift hitch # TLD1108 is the confirmed fit from Torklift. If you are looking for a hardware kit for this hitch you'd want the part # TLM8003-C1202.

expert reply by: Jameson C

0

Answer 1

Thank you for the photo - the running boards on your 2019 Ram 3500 with the 6-1/2 foot bed and the factory hitch are considered cab length running boards because they do not run underneath the length of the truck bed. Therefore, the correct Torklift…

view full answer...

Answer 2

Yes, the TorkLift SuperHitch Magnum Trailer Hitch Receiver #TLD1109-30 will fit your 2019 RAM 2500 Power Wagon with the 6-1/2' bed. According to the installation instructions no modification of the spare tire location/support is needed. The…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 8

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 9

The proper extension for your setup would be the one that allows you to have clearance of your hitch mounted accessory and also allows you to still be able to pull the steps down. If the receiver tube sticks out past the camper too far then you will…

view full answer...

Answer 10

The support braces in the HappiJac Truck-Mounted Camper Tie-Downs #LC182860 are going to attach to the cross frame to provide support for the anchors which will bolt through the bed wall and into the braces. The rear anchors will bolt through the…

view full answer...

Answer 11

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 12

The current Torklift tie down part #TLD3101 that you have installed on your 1997 Dodge Ram 3500 only fits if you have the factory hitch. If you go with the SuperHitch part #TLD1100 you would need to change your rear tie down to the part #TLR3503.

view full answer...

Which Torklift Hitch/Replacement Hardware Fits 2014 Ram 3500

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching