Does Yakima SkyRise 3 Tent Fit on Yakima LockNLoad Platform Rack

Question

Question:

I have Yakima skyrise 3. It’s mounted on Rhino-rack cross bars with rhino-rack backbone on a 2020 Jeep JL rubicon 4 door. If I mount this platform on my crossbars, can I attach the rooftop tent to it?

asked by: Grady F

0

Expert Reply:

Yes the Yakima SkyRise 3 part # Y07437 that you referenced is perfectly compatible with the Yakima LockNLoad Platform Rack # Y05047-39 that you also referenced.

expert reply by: Jameson C

0

Answer 1

Yes, the Crossbar Clamps for Yakima LockNLoad Roof Rack part #Y05039 is what you need to install the Yakima LockNLoad Platform Roof Rack part #Y05044 on the Yakima OverHaul HD Truck Bed Ladder Rack part #Y01151-5868 which is a confirmed fit for your…

view full answer...

Answer 2

The best option I have to install a 12 volt power outlet in a truck bed would be to use the Hopkins 12-Volt Power Socket with Power Wire and Fuse Assembly part #HM55115 and wire this directly to the battery. This would need to be wired directly to…

view full answer...

Answer 3

Yes, the Rhino-Rack Pioneer Platform #RR42115BF that you referenced is confirmed as a fit for Yakima round bars so it will work well for you.

view full answer...

Answer 4

There are currently two Rhino-Rack Universal Pioneer Platform Racks that will work with the Yakima OverHaul HD Truck Racks like part #Y01151-58. The Rhino-Rack Universal Pioneer Platform Rack part #RR42114BF which is 48" long x 38" wide and…

view full answer...

Answer 5

I spoke with Yakima about the Yakima LockNLoad Platform Rack like part #Y05047-39 and they informed me that Rhino-Rack Pioneer Rack Accessories should work but this is not something they can test. I have attached a list of these accessories for you…

view full answer...

Answer 6

I have an answer for you. I reached out to my contact at Yakima and they said that they specially make t-slot hardware for accessories that are designed to fit into LockNLoad Platforms like the #Y05044-39. With that being said, there is no way to…

view full answer...

Answer 7

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The Rhino-Rack Heavy-Duty Roof Rack Roof Rack have specific C-channels that are designed to fit specific Rhino-Rack Heavy-Duty accessories, like the Rhino-Rack Hi-Lift Jack and Shovel-Holder Brackets #RRRCB-RSHB-RJHB as an example. That's the…

view full answer...

Answer 12

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...