Availability of Leaf Spring # e94SR with Taller Height?

Question

Question:

Is there was a leaf spring with the same dimensions as e94SR Except, instead of 4 1/4 I think I need a 4 1/2 inch on the height of D?

asked by: Vince

0

Expert Reply:

The D dimension of the # e94SR is close enough to the 4-1/2 inch figure it would not be an issue. We don't have anything that matches everything else with just that dimension different.

expert reply by: Jameson C

0

Answer 1

I can tell you how to determine the correct leaf spring replacement, though those numbers don't have anything to do with size. They are probably a serial number or some other type of manufacturer ID but nothing of consequence. Instead, the best…

view full answer...

Answer 2

A 3 inch diameter trailer axle is very commonly a 6k axle so you are on the right track with your estimate on the capacity. We have the part #e94SR which is a 6k leaf spring that has 6 leafs like you need and is 26 inch from eye to eye.

view full answer...

Answer 3

From what I can find, for 5200 lb axles you will want 29.5 inches between the hangers center to center and 33.25 inches axle center to center for double eye springs in most cases. Your equalizers and shackle straps will take up some of that…

view full answer...

Answer 4

We have a 6-leaf 6k axle leaf spring with part #e94SR you could use on your 2016 Cruiser Lite 5th wheel that would give you a little more height. These are 26 inches long which is a really common size.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 8

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Availability of Leaf Spring # e94SR with Taller Height?

Product Page this Question was Asked From

Continue Researching