Fulton F2 Jack With Mounting Hardware

Question

Question:

Does the Fulton F2 available as the single wide track without mounting hardware , I need it to be similar to # F1413040134 ? Thank you.

asked by: Brian T

0

Expert Reply:

Check out the Fulton F2 Swing-Up Trailer Jack # F1413040134. This is an F2 jack with a single wide wheel track, except it comes with 2 U-bolts for installation that you could just discard.

expert reply by: Jameson C

0

Answer 1

The Fulton mount #F500276 hole to hole length center on center is 5-1/2 inches and the hole to hole width center on center is 4-1/2 inches. The overall is 6 by 5 inches. The bolts included are 7/8" with threads that are 16 course.

view full answer...

Answer 2

For a Fulton F2 trailer jack that will fit your 5 inch tall by 2 inch wide frame I recommend #F1413140334. This is a single wheel model that will be easier to turn compared to a dual-wheel model. The jack is rated for 1,600 pounds. I have included a…

view full answer...

Answer 3

If you want to avoid the hassle of trying to match up a new jack to the old mount on your trailer you can simply bolt on a new side-mount swivel jack like the Fulton F2 #F1413040134. The swiveling F2 fits 3 x 3 and 3 x 4 trailer tongues, features…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 11

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...