Which Solera Awnings Come with a Wind Sensor

Question

Question:

Is there a wind sensor available for the Solera XL 9-8 and the Solera 12v 8 awnings? Also, it appears that the 8foot awning comes with an exterior switch as well as a wired interior switch, but I see no mention of that with the XL version Is that also included with the XL?

asked by: Jerry H

0

Expert Reply:

The Solera Smart Arm Wind Sensor Kit part # LC715123 is only available for the Solera Smart Arm 12V Power RV Awnings like part # LC405523. It cannot be added to any of the other systems such as the Solera 18V Power RV Awning.

The Solera XL Power Awning Roller Assembly come with both inside and outside operation.

expert reply by: Conner L

0

Answer 1

The Solera Smart Arm Wind Sensor part #LC715123 can only be used with the 12 volt Smart Arm assemblies like the #LC759516 and cannot be used with the 18 volt kits.

view full answer...

Answer 2

I do have an option for you but you cannot add the Solera Smart Arm Wind Sensor Kit part #LC715123 to a Solera 18V Power RV Awning. The only way to obtain the wind sensor is to upgrade your arms using the Solera Smart Arm 12V Power RV Awning…

view full answer...

Answer 3

If the awning you have is a 12 volt Solera power awning you can add the wind sensor part #LC715123 but if you have any other awning setup then this would not work and we do not have any other options that would.

view full answer...

Answer 4

We might have some solutions that would work for you. If your leaf springs are mounted to the UNDERSIDE of your axle beam, the Dexter #K71-385-00 Over/Under Axle Conversion Kit would allow the spring pack to be relocated to the top of the axle.…

view full answer...

Answer 5

Great question, thanks for reaching out. You are looking for the LED Fabric Light Kit with Switch/Plate for Solera RV Awning - 21' Long #LC674283. This will work with the Solera 12V XL Power RV Awning - 21' Wide - Extra-Long…

view full answer...

Answer 6

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to…

view full answer...

Answer 7

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need…

view full answer...

Answer 10

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...