Recommend Sumospring for 2019 Toyota Tundran Towing 1600-lbs Camper

Question

Question:

I am looking at getting a camper that weighs 1300 to 1600 pounds depending on brand, which SumoSpring would you recommend? 1500 or 2800 pound rated one?

asked by: Ray

0

Expert Reply:

The SumoSprings Solo Custom Helper Springs # SSR-610-47 with a capacity of 1500-lbs will be a good choice since that camper is really only going to have a tongue weight of around 240-lbs maximum. If you're also carrying loads in the truck bed, these will give you the additional support you need. The SumoSprings are a great choice because they offer progressive load control, meaning they're softer when they first engage and will get stiffer as more weight is applied, so they're not going to effect your unloaded ride quality.

If you're planning on carrying heavier loads in the truck bed when you're not towing, going up to the # SSR-610-54 would be a good idea since they'll provide the additional support needed for those.

expert reply by: Erik B

0

Answer 1

The SumoSprings I recommend for your 2016 Toyota Tundra to help with sag are the SumoSprings Solo Custom Helper Springs #SSR-610-54. Since you have a more constant load on the rear of your truck with the heavier camper, and you also tow, the best…

view full answer...

Answer 2

For your 2018 Toyota Tundra SR5 4x4 I recommend the SumoSprings Solo Custom Helper Springs - Rear Axle #SSR-610-54 to give you the load leveling you desire. The SumoSprings have more of a progressive load support than the Timbren springs. Timbren…

view full answer...

Answer 3

The best way to choose the correct Sumo Springs for your 2001 Toyota Tundra is based off the tongue weight of the trailer you're going to be pulling and the overall capacities on your vehicle. The payload capacity on a 2001 Tundra is a…

view full answer...

Answer 4

For the best ride quality, you'll want to try to match the weight capacity of the SumoSprings application you use to the amount of weight what you'll be towing/hauling will apply to the rear suspension. The tongue weight of your…

view full answer...

Answer 5

Since you want support, ride quality, and would prefer an economical price the SumoSprings Solo kit part #SSR-610-54 would be exactly what you want for your 2016 Toyota Tundra. This is the best blend of the things you are wanting and will do a great…

view full answer...

Answer 6

According to ALLDATA, when reinstalling the rear u-bolt for the SumoSprings Solo Custom Helper Springs part #SSR-610-47 on a 2008 Toyota Tundra you will need to apply 74 ft-lb of torque.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...