SumoSprings for 2016 Toyota Tundra to Help With Sag

Question

Question:

I have a 2016 doublecab tundra. Leveled on 35s. Put a fiberglass camper shell on it and then the rear went down 1 inch. I do pull trailers, what would the springs do for my reared height wise

asked by: Rodney D

0

Expert Reply:

The SumoSprings I recommend for your 2016 Toyota Tundra to help with sag are the SumoSprings Solo Custom Helper Springs # SSR-610-54.

Since you have a more constant load on the rear of your truck with the heavier camper, and you also tow, the best option is going to be the highest-rated springs, which these are (2,800 lbs). These SumoSprings will help level out your Tundra and make it handle better, particularly when you are towing.

I have added a link to a video review for you as well of the SumoSprings Solo Custom Helper Springs # SSR-610-54.

expert reply by: Kyle S

0

Answer 1

The SumoSprings Solo Custom Helper Springs #SSR-610-47 with a capacity of 1500-lbs will be a good choice since that camper is really only going to have a tongue weight of around 240-lbs maximum. If you're also carrying loads in the truck bed,…

view full answer...

Answer 2

According to ALLDATA, when reinstalling the rear u-bolt for the SumoSprings Solo Custom Helper Springs part #SSR-610-47 on a 2008 Toyota Tundra you will need to apply 74 ft-lb of torque.

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Hey Tim, thanks for the picture of your current brake assemblies. While what you have doesn't look exactly like a free-backing setup you definitely can replace what you have with them. For that I would go with the etrailer part #AKFBBRK-35 which…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 10

Yes we do have a set of Timbrens that fit your 2024 Toyota Tundra with the part #T45MR. These can give you up to an additional 6,000 lbs of suspension support.

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...