How To Find Return Line When Installing Derale Series 8000 Plate-Fin Transmission Cooler

Question

Question:

How do I find out which I’d the return line to the transmission on the connections to the radiator. I’m not bypassing I’m going to use both thank you for your help

asked by: Casey

0

Expert Reply:

In regards to installing a transmission cooler like the Derale Series 8000 Plate-Fin Transmission Cooler part # D13503, you will need to identity the return line. In order to do this, take a few short laps around the block and then grab one of the two transmission hoses feeding the radiator. The cooler of the two hoses will be the return line.

Please note, for GM applications you'll also most likely need the Derale Snap-In Radiator Adapter Fitting part # D13035.

expert reply by: Conner L

0

Answer 1

The Furrion cameras, like what comes in the part #FOS43TASF that replaced the part you referenced, are only compatible with their specific monitors. If you are looking for a camera system that allows you to use your smartphone as the monitor then I…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The most likely cause of the "no signal" error you are receiving with the Furrion Vision S Wireless RV Backup Camera System part #FOS43TASF is due to an interruption on the camera's power wire. Make sure that the camera is receiving…

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Since your trailer has the bracket #FRCBRKT-BL that would mean your trailer has the Furrion pre-wiring which is very common for newer RVs. The part #FOS43TASF is a fit for this and would be a really easy install. This gives you a monitor with a 4.3…

view full answer...

Answer 6

The replacement glass cover for your Furrion 2-in-1 Range Oven is part #C-FSRE21SA-SS-003. This is compatible with the 17" ovens #FSRE17SABL and #FSRE17SASS as well as the 21" oven #FSRE21SABL.

view full answer...

Answer 7

Yes you can upgrade the 5 inch monitor of your Furrion Vision S system with a 7 inch one with the part #FR47FR and you'd be set.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The Replacement Glass Top for Furrion 2-in-1 Range Oven part #C-FSRE21SA-SS-003 is what you need to replace the glass top on a Furrion 2-in-1 Range Oven (FS17WB4A-BL) which is the same as our Furrion 2-in-1 Range Oven part #FSRE17SABL that is now…

view full answer...

Answer 10

The Furrion camera system we have is a closed system and would not be compatible with the in-dash display so you would need to purchase GM's camera system to be able to connect to your display instead of having another monitor. If you do end up…

view full answer...

Answer 11

The pre-wiring of Furrion pre-wired RVs is basically just two wires as well as the Voyager harness like part #PSVCWVCMS130AP. One wire is the power wire which is the running light circuit and then the other is the ground so it really would just be a…

view full answer...