Threaded Hitch Pin Replacement for Transit Bike Rack

Question

Question:

Need threaded pin for Transit bike rack

asked by: Steven R

0

Expert Reply:

The Anti-Rattle Hitch Lock for SportRack Bike Racks and Cargo Carriers part # SR0901 should fit as a replacement and get you back out exploring. We do not carry the Transit rack it appears to have a standard sized 1/2x20 threaded bolt.

I've linked a video for you to check out on it.

expert reply by: Randy B

0

Answer 1

The diameter of the pin on the Trailer Hitch Receiver Lock #e98879 is 1/2 inch. I spoke with my contact at Yakima to learn more about your bike rack. The rack you have is a ROC 1.25. This bike rack is designed to use a threaded hitch bold. For a…

view full answer...

Answer 2

The replacement Wheel Loop #05004700000 that you referenced does feature a square 1-1/4 inch opening for the support tube so it's possible that it will work as a replacement on your Transit Flatbed 2DLX rack. The square opening on the cradles…

view full answer...

Answer 3

When a key will not turn in a lock with an item like Master Lock #1480DAT sometimes a very gentle tap with a small hammer will help to fully seat the key in the tumbler. You can also try a light sanding of the key's teeth with fine grit sandpaper…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 9

The Kuat Sherpa 2.0 #SH22G and the NV 2.0 #NV22G that you referenced are both excellent platform-style racks that will hold your bikes by the front wheels with no frame contact. These are top-of-the-line carriers and you really would not go wrong…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

Our etrailer Trailer Hitch Receiver #e27KR you found is our most economical custom fit receiver for your 2023 Honda Pilot Touring edition. For the wiring you can select from either the 4-Way #C48ZV or the 7-Way #C35ZV depending on the types of…

view full answer...

Answer 12

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...

Threaded Hitch Pin Replacement for Transit Bike Rack

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching