Are Inflation Valves Included with the AirLift 1000 Air Helper Springs for a 1995 Crown Victoria

Question

Question:

Is there a airbags valve that I can go to a air pump and pump air in it on a 95 crown Vic for the airbags suspension

asked by: Roleisha

0

Expert Reply:

Yes, the AirLift 1000 Air Helper Springs, # AL60798, do come with inflation valves so you can fill the air bags at the location of your choosing. The recommended method for installing these air bags is using the tee. You will route an air line from each air bag to the tee and then one line to the inflation valve. This will ensure that your air bags are filled evenly.

If you think that the load in the rear of your vehicle will be uneven from one side to the other, then you can also install two inflation valves and not install the tee. This will allow you to fill each air bag independently and not allow the air to migrate from one bag to the other when a greater load is placed on only one side of your vehicle.

I have attached a link to the installation instructions for you to check out.

expert reply by: John H

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 9

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 10

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 11

Thanks for the picture! For your 2023 GMC Sierra 1500 with adaptive ride control you'll want the Air Lift LoadLifter 5000 Air Helper Springs item #AL57388. This air bags have a 5,000 lbs load leveling capacity that will keep the rear end of your…

view full answer...

Answer 12

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...