Can the Universal Cam-Door Lock Be Used on 42 Inch Doors

Question

Question:

Are these strong enough for rear cargo doors on a farm grain truck with 42inch sides?

asked by: Tim P

0

Expert Reply:

The Universal Cam-Door Lock for Enclosed Trailers # 383200 that you referenced are the same kind of door latches that are used semi-truck trailers. As long as they are installed properly you should have no problem with them on your grain truck.

expert reply by: Jameson C

0

Answer 1

The cams for the end of the pipe for cam-door lock #383200 basically are compression fit into the end of the pipe you use (not included). They can be tacked if need be but welding is not required.

view full answer...

Answer 2

Yes, the cams (as well as the handle) need to be welded to a 34" Schedule 40 Plumbers Pipe with a 1.06" outer diameter for proper installation of the Cam-Action Lockable Door Latch Kit #383200. To keep the pipe from dropping down when the…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Can the Universal Cam-Door Lock Be Used on 42 Inch Doors

Product Page this Question was Asked From

Continue Researching