How To Use Weight Distribution System On Trailer With No Room On Tongue/Frame

Question

Question:

I have a 2006 Rockwood Rhino pop up trailer that has battery and propane plates that obstruct the area until about 36 inches. I was hoping to utilize the Husky 32215 WD hitch with sway control. That only allows me to reach 30.5 inches, what options do I have? Thanks for your help!

asked by: Michael S

0

Expert Reply:

The best option to install a weight distribution system on a trailer with the tongue obstructed would be to use a chain style system with chain hanger brackets that bolt to the frame, the Strait-Line Weight Distribution System part # RP66082 with Chain Hangers for Reese Weight Distribution Systems part # RP58305 is what I recommend.

expert reply by: Conner L

0

Answer 1

The Curt #C17063 MV weight distribution system is designed for trailers with tongue weights ranging from 1000 to 1400 lbs, so it would be over rated for your trailer, and would be ineffective. If the maximum weight of the trailer and its contents…

view full answer...

Answer 2

Due to the importance of a properly functioning break away system, it would be best to leave the existing break away battery in place and add an additional battery for powering the jack. A standard automotive or small deep-cycle 12 volt battery would…

view full answer...

Answer 3

I do not recommend modifying a shank for a weight distribution hitch or cutting off any part of the shank; there is no way to guarantee any modified shank can work. Additionally, even though we do not carry EA-Z Lift products, I would be strongly…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

How To Use Weight Distribution System On Trailer With No Room On Tongue/Frame

Products Referenced in This Question

Featured Help Information

Instructions

Continue Researching