What Heavy Duty Hitch with 2" Receiver is Available for a 2020 GMC Sierra 3500

Question

Question:

will this fit a 2020 GMC 3500?

asked by: Steve R

0

Expert Reply:

I have a solution for you but the # BWHDRH25198 is not going to fit on the 2020 GM Sierra 3500. Instead, I recommend using the Curt # C15400 which will have a comparable capacity and is also a 2" receiver. I really like Curt hitches because of the quality of the powder coating, which is important because it's going to fight off rust/corrosion much better than some of the other options.

expert reply by: Erik B

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 3

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 4

I would discourage the use of an adapter for use of 2 inch accessories in 1-1/4 inch trailer hitch receivers. The reason is that the adapter places the carrier farther away from the rear of the vehicle and hitch, creating additional torque that 1-1/4…

view full answer...

Answer 5

The current Torklift tie down part #TLD3101 that you have installed on your 1997 Dodge Ram 3500 only fits if you have the factory hitch. If you go with the SuperHitch part #TLD1100 you would need to change your rear tie down to the part #TLR3503.

view full answer...

Answer 6

I have attached a photo of the B&W Heavy-Duty Trailer Hitch Receiver, part #BWHDRH25198 you asked about. I have noted the mounting holes on the photo you can check out. The distance center-to-center from the front mounting hole to the second is…

view full answer...

Answer 7

The Hole spacing for the B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25198 are as follows(all measurements are for center of hole to center of hole). 34" Width Frame -Front holes- 28-7/8" -Middle and rear holes- 29-1/2"…

view full answer...

Answer 8

The distance from the bottom of the frame to the top of the 2" receiver of the B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2" #BWHDRH25198 you were looking at is 7-3/8" as shown in the included diagram. I…

view full answer...

Answer 9

Yes, check out the picture I attached that has the vertical distances from where the hitch mounts to the frame of the vehicle down to the hitch tube. Since you need at least 6 inches this would clear that by 1-3/8 inches.

view full answer...

Answer 10

I am unfamiliar with the Barden Bumper and in my research, I could not find any specific information regarding the Barden Bumper. Our trailer hitches are not tested with aftermarket bumpers. We have two bumpers that have been determined to be a fit…

view full answer...

Answer 11

I spoke with my contact at Curt to obtain the mounting bolt hole locations for the Trailer Hitch Receiver, #C15300 on a 1993 Ford F-150. I have attached a picture to illustrate these measurements. As for repositioning the spare tire, you may need to…

view full answer...

Answer 12

For your 1987 Chevrolet C/K Series Pickup the B and W hitch part #BWHDRH25198 that you referenced would work really great if you had a deep drop bumper but if instead you had a standard bumper you'd want the standard version of this hitch…

view full answer...

What Heavy Duty Hitch with 2" Receiver is Available for a 2020 GMC Sierra 3500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching