Relacement Hardware for the Curt Trailer Hitch Receiver part # 13534

Question

Question:

Hello, my friend gave me his old hitch for 2008 highlander. Had no bolts i see that you guys have them in the picture and i wanted to ask if i can get it separately. And how much would just those bolts would cost me. I think its 6 bolts

asked by: Gurami D

0

Expert Reply:

We do offer replacement hardware for the Curt Trailer Hitch Receiver part # 13534.

Just enter part # RHK in the search box on our website. Then enter 13534 in the Hitch Item Number box. Select Curt From the dropdown box and order it. Your hardware kit will be assembled for you. It's that easy.

expert reply by: Randy B

0

Answer 1

The install hardware of the Curt hitch #13534 are Grade 5 steel bolts in the size of M10x1.25. They are zinc coated.

view full answer...

Answer 2

You'll need (6) M10 - 1.25 x 30 Class 10.9 hex bolts and (6) 3/8 inch conical toothed washers. We offer them in the #RHK kit you'd looked at, On the product page, you'll input the hitch part number and choose the hitch…

view full answer...

Answer 3

Most Vehicles and hitches have their own specific hardware to insure proper fit and towing capacity. Our #C13149 hitch includes a hardware kit and installation guide. I attached a video on the installation for your convenience. The hardware specs…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 10

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 11

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Relacement Hardware for the Curt Trailer Hitch Receiver part # 13534

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching