Replacement Top Strip for Thule Aero Crossbars

Question

Question:

I have a Thule roof rack that need a passenger side end cap and both top channel cap or rubber replacement strip. I found the end cap on your site but cant locate the replacement strip...

asked by: Chris A

0

Expert Reply:

If the crossbars are the Thule Aeroblade style you'd want the part # TH853354407 or if they are the newer WingBar Evo bars you'd need the # 1500052989.

expert reply by: Jameson C

0

Answer 1

To replace the rubber strips in the top of your 53" Thule WingBar Evo Crossbars #TH711420 you need the Replacement QuickAccess Interface Top T-Track Strip #1500052989. This comes with both sides of the strip, but it is one piece so you will need…

view full answer...

Answer 2

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 3

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 6

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 7

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 10

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 11

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Answer 12

The squeaking noise on your trailer is probably coming from the joints in the suspension creating metal to metal friction. So, unless your original Equa-Flex Cusioned Equalizers are damaged or corroded, what will make the biggest difference is to…

view full answer...

Replacement Top Strip for Thule Aero Crossbars

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching