Suspension Enhancement for 2019 Nissan Frontier 4x4

Question

Question:

Will the SSR-610-40 or 47 work on my 2019 Nissan Frontier 4x4. Also why would I choose to 40 1000 lbs capacity versus the 47 15000 lbs capacity? My payload rated capacity is 1,157 lbs.

asked by: Richard M

0

Expert Reply:

We have Timbren suspension enhancement kits that fit your 2019 Nissan Frontier 4x4 with the part # TTORTUN4L but we do not have any SumoSpring kits that fit your vehicle. This kit will give you an additional 3,000 lbs of suspension support.

expert reply by: Jameson C

0

Answer 1

We do have a nice selection of suspension enhancement products available for your 2015 Nissan Frontier, such as the TorkLift StableLoad Rear Suspension Upgrade #TLA7311 that you mentioned, however I'm not sure that any of them will provide you…

view full answer...

Answer 2

The Timbren kits like the #TTORTUN4L that you referenced do not raise the suspension of the vehicles they install on. They only reduce sag when the vehicle has weight on it from either a trailer tongue or cargo. There will be about 1.5 inches of…

view full answer...

Answer 3

You can install the Timbren Rear Suspension Enhancement System #TTORTUN4L on your 2019 Nissan Frontier with a suspension lift. In order to do so, you need to add the appropriate amount of spacers that will allow you to wind up with between 1/2"…

view full answer...

Answer 4

The Brophy Recessed Trailer D-Ring Tie Down with Backing Plate #RR5K is not application-specific so its preferred method of installation will vary from trailer to trailer. The main factor is the thickness of the material to which it will be mounted.…

view full answer...

Answer 5

Just like the SumoSprings Solo Custom Helper Springs #SSR-612-47, the Timbren Rear Suspension Enhancement System #TTORTUN4L will also replace the factory bump stops and mount directly over the axle, there is no offset. As far as actual lift goes,…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...