Is Adapter Module Required for 2015 Chevy Silverado 2500 to Work with Hydrastar EOH Actuator

Question

Question:

Do you have to have the interface module with a 2015 Silverado 2500? Thanks

asked by: Kevin D

0

Expert Reply:

Yes, you will need to use the Adapter Module # HBA-CAM so that the OEM brake controller on your 2015 Chevy Silverado 2500 communicates with a Hydrastar EOH Actuator like # HBA16 or # HBA-10.

expert reply by: Jon G

0

Answer 1

The CAM from the Carlisle Control Adapter Module #HBA-CAM stands for Control Adapter Module. The purpose of this unit is to adapt the Carlisle HydraStar Electric-Hydraulic Actuator #HBA16 to the following brake controllers. Ford factory controller…

view full answer...

Answer 2

The newer factory brake controllers, like on your 2022 Chevy Silverado, are generally fine with an EOH actuator like the Dexter DX Series Electric Over Hydraulic Brake Actuator #K71-651. But there are times when there are issues which is why I…

view full answer...

Answer 3

The Dexter Electric Over Hydraulic Brake Actuator, #K71-651, is not compatible with the 2007 to current GM integrated trailer brake controllers. The adapters made for other systems are not designed to be used with the Dexter EOH systems. There are 2…

view full answer...

Answer 4

Integrated brake controllers like what you have in your 2015 Chevy Silverado are pretty inconsistent with how they work with electric over hydraulic actuators. Sometimes they work totally fine, sometimes not at all, or like in your case the function…

view full answer...

Answer 5

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 11

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Is Adapter Module Required for 2015 Chevy Silverado 2500 to Work with Hydrastar EOH Actuator

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching