What is the Purpose of the Carlisle Control Adapter Module # HBA-CAM

Question

Question:

What does HBA-CAM stand for, I know that HBA stands for hydaulic brake actuator but what CAM stand for and what is the purpose of this product.

asked by: Jose T

0

Expert Reply:

The CAM from the Carlisle Control Adapter Module # HBA-CAM stands for Control Adapter Module. The purpose of this unit is to adapt the Carlisle HydraStar Electric-Hydraulic Actuator # HBA16 to the following brake controllers.

Ford factory controller from 2007-2008
GM/Chevrolet factory controller 2007-Present

I attached installation instructions for this product for you to check out also.

expert reply by: Jameson C

0

Answer 1

That is correct. If your 2021 Wrangler Unlimited has the connector located under the dash to the left of the steering column near the top of the e-brake pedal as shown in the provided photo, you'd use the #3073-P harness to connect the #90195…

view full answer...

Answer 2

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 3

The exact replacement hub assemblies you need for your BD2-545-17 are the etrailer Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 #AKHD-545-35-K that you referenced.

view full answer...

Answer 4

The 1.75 inch inner diameter for bearing is #25580, which is only used on mostly 7,000 lb to 10,000 lb axles, as opposed to a 3,500 lb camper. Additionally, there isn't a hub with that bearing along with a bearing that has a 1.25 inch diameter,…

view full answer...

Answer 5

The first thing I would do is check the brake output circuit on the 7-way of your tow vehicle. You will want to use a circuit tester like our part #3808 to check for voltage at this circuit when the manual override of your brake controller is…

view full answer...

Answer 6

The clicking noise you heard typically occurs when the factory brake controller isn't compatible with electric over hydraulic brake systems. Since everything worked fine up until recently, the problem most likely does lie with your #HBA-CAM.…

view full answer...

Answer 7

Integrated brake controllers are notorious for not always working well with electric over hydraulic actuators. Sometimes it's just easiest to replace the controller with aftermarket. What actuator does your trailer have? If it is a Hydrastar like…

view full answer...

Answer 8

Yes, we have everything you need to convert the electric drum brakes on your 2014 Kaufman Car Wedge Trailer to electric over hydraulic disc brakes. In order to do this you are going to need disc brake assemblies, trailer hubs, brake lines, and an…

view full answer...

Answer 9

The #HBA-CAM adapter will not interfere with the actuator working on your 2006 Dodge Ram that does not require the adapter. It basically just puts enough load on the output circuit so that the controller thinks a trailer is connected. That additional…

view full answer...

Answer 10

It's possible. Here's Cargo Towing Solutions troubleshooting procedure for if the actuator won't run, or runs continuously: Verify that the trailer and tow vehicle are wired according to the electrical schematic shown below. Perform the…

view full answer...

Answer 11

What we have found is the integrated trailer brake controllers on trucks can be very temperamental when used with electric over hydraulic brakes. I do recommend using a HydraStar Electric Over Hydraulic Actuator Adapter Module #HBA-CAM with your…

view full answer...

Answer 12

It may be possible to change your studs from 1/2" to 9/16" so long as the studs are drive-in (as opposed to threaded); also, the length and knurl diameter needs to be the same. For example, the Kodiak Wheel Bolt - 9/16" Diameter x…

view full answer...