Replacement Hardware Needed for Curt 13019 Trailer Hitch on a 2001 Ford Ranger

Question

Question:

I have a 2001 Ford Ranger with a Curt hitch. I am looking for the mounting hardware 13019-BK. Can you help? Thanks Steve

asked by: Steve F

0

Expert Reply:

To get replacement mounting hardware for the Curt # 13019 trailer hitch on your 2001 Ford Ranger you will need part # RHK.

Simply go to the product page and select "Curt" from the drop-down manufacturers menu and then input "13019" into the box for your hitch number and we will send you all of the hardware that is needed.

The installation instructions for this hitch are linked to this page for you to reference as well.

expert reply by: Jon G

0

Answer 1

The Curt hitch that fits your 2008 Ford Ranger part #13019 fits with a full size spare. I attached a picture that shows the hitch installed along with a full sized spare.

view full answer...

Answer 2

The difference between the Curt Class III Receiver Hitch part #13019 and the Curt Class III Receiver Hitch part #13138 is strictly aesthetics. The square tube option is a bit more cost effective and it matches the body lines on your 1992 Ford Ranger…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Generally speaking wheel mount only bike racks are preferred. Especially for people with carbon fiber bike frames since frame mounts aren't recommended at all with them otherwise damage could occur. For other frame designs people still prefer…

view full answer...

Answer 11

We have just what you need. If you type RHK in the search box on our website it will take you to the replacement hardware kit product page. You will then simply type the number of the hitch you need hardware for in the box that is labeled Hitch Item…

view full answer...

Replacement Hardware Needed for Curt 13019 Trailer Hitch on a 2001 Ford Ranger

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching