Hitch for a 2019 Ford Mustang Bullitt with Both Active Exhaust and Magneride Suspension

Question

Question:

Hey guys, I called Curt directly, and the tech guy said flat out their hitch does NOT fit cars with active exhaust. I was bummed, but after reading a review from a Nathan on a 2018 GT with AE but probably not magneride, or MR, Im wondering if the Draw-Tite would fit my car. Read his review and didnt quite understand the additional steps he needed to take to install the hitch, but he did install it, so I should be able to figure it out. I just wanted to make sure he didnt have to modify anything, so if one of you could contact him, and see if he wants to help, itd be great. Hoping I can fit the DT, and apparently its tucked up 1/2inch more than the Curt, so awesome. It only has 3 vs 4 attachment points, but it shouldnt be an issue with just 1K lbs our cars can handle. Thank you.

asked by: JC

0

Expert Reply:

I can't confirm the fit of the # C11405 hitch on your GT model with Active Exhaust and Magneride. I also can't put to you in contact with a customer just because they posted a review. A Customer named Pete also installed this on a 2018 GT and stated he had to move the active valve performance exhaust and clips to the back of the sensor to attach it back to the frame. He said it was a minor adjustment but again don't know if there was magneride but likely so on that model. He said the install took about 60 minutes compared to the 40 minute estimate on a Mustang without the additional changes required.

The Draw-Tite # 24928 is also not a confirmed fit but with the reviews you may figure something out as these hitches attach in the exact same location and are very similar. You will need to use all attachment points for the rated capacity.

expert reply by: Jason S

0

Answer 1

Thule doesn't have any trunk mount bike racks that fit your 2019 Ford Mustang, but we do have some other options for you. If your Mustang is a convertible then Yakima has their FullBack #Y02634 trunk mount rack that you can use. If you have…

view full answer...

Answer 2

According to Draw-Tite, their #24928 Class I hitch will fit a 2018 Mustang GT convertible with the active exhaust. If you'll be towing with the hitch, you'll also need a trailer wiring harness, part #118487, a #3594 ball mount and for…

view full answer...

Answer 3

The hitches we offer for the Toyota Sienna have a maximum rated tongue weight capacity of 350 lbs. This is true for all model years from 2010 through 2013 (I checked several since I do not know your specific year). I have provided a link to our…

view full answer...

Answer 4

A professional could install trailer hitch #75902 for your 2013 Nissan Rogue in about an hour or so. You would have to check local shops in your area to determine what rate they charge per hour. You can even print out the instructions which I have…

view full answer...

Answer 5

We certainly do! If you live nearby, or will be traveling near the Wentzville MO area, we'd be happy to install a hitch for you. Give our Customer Service folks a call for an appointment or for more details.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Hitch for a 2019 Ford Mustang Bullitt with Both Active Exhaust and Magneride Suspension

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching