Will Fastway Weight Distribution Fit frame of KZ RV Sportsmen Classic 181BH

Question

Question:

I have a KZ RV Sportsmen Classic 181BH with a 2x3inch tongue frame. Will this fit?

asked by: Taylor

0

Expert Reply:

Yes, the frame brackets of the Fastway weight distribution system part # FA92-00-0600 will fit great on a 2 inch by 3 inch trailer frame. I also looked up the GVWR of your KZ RV Sportsmen Classic 181BH and this system would work in that regard as well.

expert reply by: Jameson C

0

Answer 1

The etrailer.com #e99044 did receive an upgrade and should have fluid in the gauge. With that being said, they will all have an air bubble like this and it is perfectly good to use.

view full answer...

Answer 2

Both the Sherline Trailer Tongue Weight Scale #5780, and the etrailer Tongue Weight Scale #e99044 will accurately measure the tongue weight on your trailer as long as the tongue weight is less than 2000lbs. With that said I prefer the etrailer…

view full answer...

Answer 3

This is a really good question. I sent it to our engineer and he told me that the gauge has a 3%,2%,3% margin of error. This means that in the first third of its range, it is +/- 3% of the actual tongue weight, the middle of its range it is +/- 2%,…

view full answer...

Answer 4

Basically, one friction-style sway control can be used for trailers with up to 6,000-lb GTW. If your trailer's GTW is between 6,000 lbs and 10,000 lbs, you will need two sway-control units, one on each side of the trailer. You will also want…

view full answer...

Answer 5

With your trailer being so new it sounds to me like the real issue is with your weight distribution hitch. Your Husky Centerline is most likely rated too high for the tongue weight of your trailer and is giving you this rough bouncy ride. The GVWR of…

view full answer...

Answer 6

Whenever looking at weight distribution systems it's best to have the total tongue weight of your trailer fall in the middle of the WD rating, that way you have some wiggle room if your tongue weight varies between trips. The Fastway e2 Weight…

view full answer...

Answer 7

Yes, the dimension you mentioned is the distance from the center of the ball hole on the coupler back on the frame rails 27-30 inches for the Fastway e2 part #FA92-00-0600.

view full answer...

Answer 8

Weight distribution works to distribute the tongue weight of a trailer up to the front axle of the tow vehicle so that it will sit more level and handle/brake better. That being said the systems do not "reduce" tongue weight or allow you to…

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 10

Hey Tom, you are on the right track. I checked out your 2023 Jayco Jay Flight 284 BHS and it does have an underslung coupler so the correct B and W Continuum weight distribution would be the part #BW88FR. An underslung coupler is basically one that…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Blue Ox has an easy system for determining the weight capacity of your spring bars, whereas other companies may use measurements or printed capacity to assist. With Blue Ox, there is a 5 dimple system: No dimples means it is rated for up to 350 lbs…

view full answer...

Will Fastway Weight Distribution Fit frame of KZ RV Sportsmen Classic 181BH

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching