Replacement Circuit Board for MaxxFan Roof Vent 5100

Question

Question:

I am pretty sure the model I have is the 5100 without manual lift. The fan had been working perfectly and suddenly, when I press the on/off button it will beep but the fan does not turn on. Pressing the thermostat button, results in it turning green. I have hit the plus and minus buttons, made sure the lid is open and it simply will not come on. It appears from my research that I need a new circuit board. A couple questions ... Do I need to remove the entire fan assembly remove roof caulking etc to get to the circuit board for replacement or is there another way to replace the board without entirely removing it from the coach? Also ... the video on this part mentions and antenna. Is this an antenna for remote operation? If so, mine did not come with a remote control. It would sure be nice not to stand on a stool in the bathroom in order to operate this fan therefore do you sell the remote control device too and will it work with this fan? Thank you for your help.

asked by: Michael F

0

Expert Reply:

The circuit board # MA10A21276K is the correct part you need for your # MA00-05100K that you have. This does install an antenna so if you are missing a remote control you could then use the part # MA00A01150K to operate it with a remote.

expert reply by: Jameson C

0

Answer 1

Roof vents with fans like the MaxxFan Roof Vent w/ 12V Fan #MA00-04000K do not have a fuse anywhere in the fan itself. You will want to use a circuit tester like #PTW2993 to see if there is power getting to the fan. If it was installed by the…

view full answer...

Answer 2

You reported that you cannot use the remote on your MaxxFan 4700K to put the vent cover up and down. Let's troubleshoot. Put some new batteries in your remote. Ensure that the display comes on. Verify if your vent cover now works. Verify if other…

view full answer...

Answer 3

My contact at MaxxAir advised that there are three potential causes for the beep and no fan motion you're experiencing with your MaxxFan Trailer Roof Vent #MA00-04000K. One potential cause is that the unit was wired with incorrect polarity. Make…

view full answer...

Answer 4

For your MaxxFan RV roof vent part #MA00-05100K the correct replacement circuit board is the #MA10A21276K.

view full answer...

Answer 5

It sounds like your MaxxFan may need a new circuit board. Typically, when customers had similar issues they were able to replace the circuit board and their fan return back to normal operation. You can use Replacement Printed Circuit Board…

view full answer...

Answer 6

Yes, we are an authorized seller of MaxxAir products, including the MaxxFan Deluxe Roof Vent #MA00-06401K that you were looking at. This unit comes with a 2-year limited warranty on the vent assembly and a limited lifetime warranty on the dome from…

view full answer...

Answer 7

The correct replacement for your MaxxAir Circuit Board 10-04751ks is the following part: - Replacement Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents #MA10A04751KS As for the sensor wires, so long other wires are not damaged, I don't…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Erik, thanks for reaching out! We can definitely get you to the #ETBC7 kit building off of your Curt Trailer Connector Adapter #C57672. What you need is the Wiring Kit #5506 which has everything else in it aside from the circuit tester. If you…

view full answer...

Answer 10

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 11

We do have everything you need to install a 7-Way on your 2020 Subaru Outback Wagon so you can utilize a brake controller but we need to start off by making sure you have a 4-Way for the basic trailer lighting functions. If you don't already have…

view full answer...

Answer 12

The equivalent hub assembly to CE Smith Trailer Hub Assembly #CE13100 that has lug bolts built in is part #CE13110. The Inner and outer bearings (L44643) and races, and grease seal are all pre-packed in this fully assembled hub with marine-grade…

view full answer...