Replacement Brake Shoes for Dexter Assemblies # 23-450-451

Question

Question:

I work with Naval Air Weapons Station China Lake and we currently utilize trailers that have hydraulic and electric brakes 23-450-451. Do you carry shoes for these brake systems, and if so, what part numbers are they? Thank you for the excellent service in the past!

asked by: Lucas S

0

Expert Reply:

For the brake assembly set part # 23-450-451 that you have the shoes you need are # BP04-240 for the driver side and part # BP04-250 for the passenger.

expert reply by: Jameson C

0

Answer 1

The correct electric drum brake assemblies for a trailer with 10k axles like yours would be the part #AKEBRK-10. In order to pick out the correct drum I would need more specific info from you though like what is the wheel bolt pattern and what is…

view full answer...

Answer 2

The Dexter Electric Brake Kit #23-450-451 are the brakes you will need for your 2018 Big Tex 22GN with the 10,000lb Dexter axles. These are sold per axle so you will need 2 sets to replace all 4 of your brake assemblies. They are also sold…

view full answer...

Answer 3

Yes, the self-adjusting Electric Trailer Brake Kit w/ Dust Shields #AKEBRK-10 will work on Dexter Axle hub and drums, so long as you have the appropriate 7-bolt brake mounting flange. These brake assemblies are rated for 10,000 lb axles and only…

view full answer...

Answer 4

I was able to cross reference the Dexter Hub/Drum 8-415 to the Dexter Trailer Hub Drum Assembly part #8-430-5UC3 which should be an exact replacement. I don't have any depth measurements of the above/drum but what you would need to measure…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...