All Parts Needed to Tow Trailer With 2017 Volkswagen Golf GTI

Question

Question:

need parts to set up my 2017 VW Golf GTI for towing small bass boat with trailer. Need hitch, wiring, ball and anything additional I may need. Please send parts/products you recommend.

asked by: Marko C

0

Expert Reply:

We can get you set up with all the parts for your 2017 Volkswagen Golf GTI to tow your bass boat so you can get on the water and get fishing. Here is a list of all the recommended parts that fit your VW:

- Curt Trailer Hitch Receiver # C11412

- Wiring Harness # C59236

- Curt Drawbar # C45521

- Pin & Clip # F-4

- 1-7/8" Hitch Ball # 19256 or 2" Hitch Ball # 19258

expert reply by: Kyle S

0

Answer 1

For your 2017 VW Golf Wolfsburg Edition, I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" #C11412. If you will be doing some light towing with this hitch receiver, I recommend the ball mount #C45521 along with hitch…

view full answer...

Answer 2

I would be happy to help you. We have a couple of options for 2" hitches depending on what model your 2017 VW Golf is. I have listed them below. All are custom fit and bolt to your Golf with included hardware and will work with the Hollywood…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

Since your 2024 Telluride X-Line is not an LS or S model the correct wiring harness is the Curt #C29ZV. This will plug into the connection points in the rear cargo area and provide you with a 4-way to power your trailer's signal lights. The…

view full answer...