Does Draw Tite Hitch DT45519 Fit 2006 Chevy Silverado 3500

Question

Question:

I have a 2006 Chevy silvy3500 4x4 with a bed will it fit on my truck

asked by: Jeremy P

0

Expert Reply:

Yes, the Draw Tite hitch part # DT45519 is a confirmed fit for your 2006 Chevy Silverado 3500 long bed truck!

expert reply by: Jameson C

0

Answer 1

We haven't had the chance to install the Curt Class V Trailer Hitch Receiver #C15703 on the 2008 Chevy Silverado 2500 so I don't have exactly how far beneath the bumper the receiver will sit, however I did go out to our warehouse to take a…

view full answer...

Answer 2

I went to the warehouse and measured the Curt Trailer Hitch Receiver, part #C15703. I have attached a photo of the trailer hitch and have noted the dimensions you can check out. This is a Class V trailer hitch and it has a 2-1/2 inch receiver…

view full answer...

Answer 3

The best class V hitch for your 2002 Silverado 2500 is going to be the Curt Trailer Hitch item #C15703. This hitch is custom fit for the 2500 HD's with the 6-1/2' beds and bolts to your truck with included hardware. This hitch has a…

view full answer...

Answer 4

Curt Trailer Hitch Receiver #C15703 hangs pretty low on a 2005 Chevy Silverado 2500. From the bottom of the bumper to the top of the hitch receiver it is approximately 4 inches. I have included a picture showing the gap. A similar hitch, #C15302,…

view full answer...

Answer 5

We offer Class V hitches in both 2-inch and 2-1/2-inch sizes for your 2009 Chevrolet Silverado 2500. All are shown on the linked page. Draw-Tite's 2-inch hitch #41944 is a no-drill install since it bolts up to the bumper bracket the same way as…

view full answer...

Answer 6

Curt does not have that measurement available, but you can determine this for yourself by taking some measurements from the underside of your truck. Using the diagram I edited for you, locate the weldnut that would serve as the rear-most attachment…

view full answer...

Answer 7

The frames of the 2004 Chevy Silverado 2500 HD with short beds aren't going to be any different than standard beds or those trucks with hitches already installed, you just would not be able to install this hitch receiver as part of a dual hitch…

view full answer...

Answer 8

By mounting hole dimensions I assume you are asking about the distance between them, and that distance is 39 inches for the Draw-Tite Trailer Hitch Receiver #DT45519. That is the same distance between the mounting holes as the similar hitch from Curt…

view full answer...

Answer 9

The Draw-Tite #DT45519 is designed to be used on the 8 foot bed models of the GMC Sierra and will not fit the short bed models. That being said, we do have Class V hitches with a 2 1/2 inch receiver options available for your short bed truck. The…

view full answer...

Answer 10

I do have a solution for you; however, it will require some changes to the existing components on your truck. The Curt Hitch Extension #C45048 that you referenced does look to be your best option for getting the extension you need to tow a trailer…

view full answer...

Answer 11

You ask a very good question. A circumstance like yours where you have widely varying loads on your car hauler trailer makes use of a weight distribution hitch something of a challenge. For weight distribution systems to be effective but not cause…

view full answer...

Answer 12

For your 5th wheel towing, I recommend the 2008 Chevy 2500 with the 6.6L V8 Duramax which based on the cab and bed length as well as drive axle will have different towing limits. I've listed them below: 2500 Reg Cab Long Bed (LB) 4WD--15,500 2500…

view full answer...