No-Splice Trailer Wiring Harness for 2014 Volkswagen Jetta SportWagen

Question

Question:

I have a 2014 Jetta TDI sport wagon I purchased the hitch and wiring from you and now the dealer said they dont splice wires! Do you offer a plug in wire assembly. thanks

asked by: Stephen M

0

Expert Reply:

I do have a solution for you, but there isn't a custom plug-in T-Connector available for your 2014 Volkswagen Jetta SportWagen. The Tekonsha # 118667, you were looking at, only fits the Sedan models of the Jetta.

For a no-splice solution, you can use the ZCI Circuit Protected Vehicle Wiring Harness # 119250KIT. This universal kit uses sensors that simply clamp to your factory tail light wires so no cutting or splicing is required to install it. The ZCI sensors are able to read the signals sent by systems with pulse width modulation (PWM), which is precisely what's used on your Jetta.

expert reply by: Carla M

0

Stephen M.

5/19/2020

Thanks

Reply

Answer 1

The Curt hitch part #C11474 that you referenced actually replaced the part number 11072 that you mentioned, but it will not fit the TDI version of the SportWagen. That said the only hitch we have confirmed as a fit for the TDI model of a 2014…

view full answer...

Answer 2

We have a complete axle kit that meets your requirements, Dexter kit #7461121-EB. This consists of a 6000-lb axle with a 95-inch hub face spacing (and 80-inch spring center spacing); please refer to the linked diagram for these dimensions. The kit…

view full answer...

Answer 3

I have a solution for you but EcoHitch does not make a hitch receiver for any 2009 Volkswagen Jetta model. I checked with Ecohitch they did not start making hitch receivers for the Jetta SportWagen model's until 2010 and the Jetta sedans until…

view full answer...

Answer 4

There are only Class I trailer hitches available for the 2006 VW Jetta, see link. I recommend the Curt #C11474. The recommended ball mount is #3593. For a 1-7/8 inch ball use #19256. For a 2 inch ball use #19258. This hitch has a 200 pound tongue…

view full answer...

Answer 5

The 2004 VW Jetta will use the Draw-Tite Sportframe Trailer Hitch Receiver #24748 which is not compatible with a 2006 Jetta. It was designed for the previous generation. You instead will need the hitch #C11474 which is specifically designed to fit…

view full answer...

Answer 6

We have just what you need. If you type RHK in the search box on our website it will take you to the replacement hardware kit product page. You will then simply type the number of the hitch you need hardware for in the box that is labeled Hitch Item…

view full answer...

Answer 7

The Dico 15638 is a 10 x 2-1/4 inch brake drum/hub that used kind of an oddball bearing setup, inner bearing LM67048 and 3/4 outer bearing LM11949. None of the hub/drums we currently carry are compatible with this bearing set. If the drums are still…

view full answer...

Answer 8

Not every vehicle has a custom install wiring kit available unfortunately. Typically the vehicles that are more likely to tow will have plug and play install kits and the lighter duty vehicles that don't tow as often will need to use a hardwired…

view full answer...

Answer 9

Yes, you can use trailer wiring harness #C59496 on a 2012 Volkswagen Jetta SportWagen TDI. I have included a link to the installation instructions for you to view.

view full answer...

No-Splice Trailer Wiring Harness for 2014 Volkswagen Jetta SportWagen

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching